Datenblatt-Suchmaschine für elektronische Bauteile |
|
FIN24A Datenblatt(PDF) 8 Page - Fairchild Semiconductor |
|
FIN24A Datenblatt(HTML) 8 Page - Fairchild Semiconductor |
8 / 20 page Preliminary www.fairchildsemi.com 8 PLL Circuitry The CKREF input signal is used to provide a reference to the PLL. The PLL will generate internal timing signals capable of transferring data at 26 times the incoming CKREF signal. The output of the PLL is a Bit Clock that is used to serialize the data. The bit clock is also sent source synchronously with the serial data stream. There are two ways to disable the PLL. The PLL can be disabled by entering the Mode 0 state (S1 S2 0). The PLL will disable immediately upon detecting a LOW on both the S1 and S2 signals. When any of the other modes are entered by asserting either S1 or S2 HIGH and by pro- viding a CKREF signal the PLL will power-up and goes through a lock sequence. One must wait the specified num- ber of clock cycles prior to capturing valid data into the par- allel port. An alternate way of powering down the PLL is by stopping the CKREF signal either HIGH or LOW. Internal circuitry detects the lack of transitions and shuts the PLL and serial I/O down. Internal references will not however be disabled allowing for the PLL to power-up and re-lock in a lesser number of clock cycles than when exiting Mode 0. When a transition is seen on the CKREF signal the PLL will once again be reactivated. Application Mode Diagrams Unidirectional Data Transfer FIGURE 8. Simplified Block Diagram for Unidirectional Serializer and Deserializer Figure 8 shows the basic operation diagram when a pair of SerDes is configured in an unidirectional operation mode. Master Operation: The device will... (Please refer to Figure 8) 1. During power-up the device will be configured as a serializer based on the value of the DIRI signal. 2. Accept CKREF_M word clock and generate a bit clock with embedded word boundary. This bit clock will be sent to the slave device through the CKSO port. 3. Receive parallel data on the rising edge of STROBE_M. 4. Generate and transmit serialized data on the DS sig- nals which is source synchronous with CKSO. 5. Generate an embedded word clock for each strobe sig- nal. Slave Operation: The device will... 1. Be configured as a deserializer at power-up based on the value of the DIRI signal. 2. Accept an embedded word boundary bit clock on CKSI. 3. Deserialize the DS Data stream using the CKSI input clock. 4. Write parallel data onto the DP_S port and generate the CKP_S. CKP_S will only be generated when a valid data word occurs. |
Ähnliche Teilenummer - FIN24A |
|
Ähnliche Beschreibung - FIN24A |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |