Datenblatt-Suchmaschine für elektronische Bauteile
  German  ▼
ALLDATASHEETDE.COM

X  

EK14 Datenblatt(PDF) 1 Page - Cirrus Logic

Teilenummer EK14
Bauteilbeschribung  EVALUATION KIT SIP03 PACKAGED OP AMPS
Download  2 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Hersteller  APEX [Cirrus Logic]
Direct Link  http://www.cirrus.com
Logo APEX - Cirrus Logic

EK14 Datenblatt(HTML) 1 Page - Cirrus Logic

  EK14 Datasheet HTML 1Page - Cirrus Logic EK14 Datasheet HTML 2Page - Cirrus Logic  
Zoom Inzoom in Zoom Outzoom out
 1 / 2 page
background image
APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL prodlit@apexmicrotech.com
1
INTRODUCTION
The EK14 evaluation kit provides a convenient way to bread-
board circuits using Apex power op amps packaged in the 12-pin
SIP03 package. The amplifier may be mounted vertically with
the HS20 heat sink, or horizontally. Connections are provided
for required power supply bypassing, external compensation
components, as well as current limit resistors. A large area for
component mounting provides flexibility and makes a multitude
of circuit configurations possible.
CAUTION
Use the supplied thermal washers or ther-
mal grease between the power amplifier
and the heat sink.
PARTS LIST
Part #
Description
Quantity
HS20
Heatsink
1
EVAL16
PC Board
1
MS06
Mating Socket
1
OX7R105KWN
1µF Ceramic Capacitor
2
CSR10
.15 Ω Resistor
2
TWO7
Thermal Washer
1 package
BEFORE YOU GET STARTED
• All Apex amplifiers should be handled using proper ESD
precautions.
• Always use the heat sink and thermal washers included in
this kit.
• Always use adequate power supply bypassing.
• Do not change connections while the circuit is powered.
• Initially set all power supplies to the minimum operating levels
allowed in the device data sheet.
• Check for oscillations.
ASSEMBLY
1. On the silk screen side of the evaluation board, insert and
solder the MS06 mating socket in DUT holes 1 – 12. Be sure
each one is fully seated.
2. Solder components for your circuit. Be sure to include proper
bypassing, required compensation components and current
limit resistors. See the op amp data sheet for help in select-
ing these components. 1uF capacitors and a .15 Ω resistor
have been included with the EK12 kit but may be replaced
with other components as necessary.
3. Place the TW07 thermal washer on the heat sink over the
mounting hole for the DUT. Place a #6 screw through the
mounting hole and thread a #6 nut onto the screw at the
back of the heat sink. Do not tighten. Note that there are
two sets of mounting holes on the HS20. Holes on one edge
allow room between the DUT and evaluation board for the
MS06 socket. The holes on the other edge are for direct
through hole mounting of the DUT to the evaluation board.
It is recommended that you use the MS06.
4. Mount the DUT to the HS20 by sliding under the head of the
#6 screw and on top of the thermal washer. Tighten the nut
to the specified 8 to 10 in-lbs. (.9 to .13 N*M). Do not over
torque.
5. Install leads of the DUT into the MS06 on the evaluation board.
Use #6 self-tapping screws to secure the evaluation board
to the HS20 heat sink as shown in the assembly diagram
(Figure 1).
��������������������������������������������������������������
� � � � � � � � � � � � � � �
�������������������������������������
����


Ähnliche Teilenummer - EK14

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
Sanken electric
EK14 SANKEN-EK14 Datasheet
43Kb / 2P
   Schottky Barrier Diodes
EK14 SANKEN-EK14 Datasheet
85Kb / 3P
   Schottky Barrier Diodes
More results

Ähnliche Beschreibung - EK14

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
Analog Devices
UG-127 AD-UG-127 Datasheet
452Kb / 8P
   Evaluation Board for High Speed Op Amps
REV. A
UG-112 AD-UG-112 Datasheet
180Kb / 8P
   Evaluation Board for Single, High Speed Op Amps
logo
Maxim Integrated Produc...
MAX17681EVKITC MAXIM-MAX17681EVKITC Datasheet
2Mb / 11P
   Evaluation Kit
Rev 0; 2/16
logo
STMicroelectronics
UM0382 STMICROELECTRONICS-UM0382 Datasheet
1Mb / 32P
   Evaluation Kit
January 2007 Rev 2
logo
Maxim Integrated Produc...
MAX2043 MAXIM-MAX2043_1 Datasheet
190Kb / 7P
   Evaluation Kit
Rev 0; 5/06
MAX2170 MAXIM-MAX2170 Datasheet
446Kb / 8P
   Evaluation Kit
Rev 0; 12/06
MAX2396 MAXIM-MAX2396 Datasheet
730Kb / 13P
   Evaluation Kit
Rev 0; 5/03
MAX2410 MAXIM-MAX2410_1 Datasheet
82Kb / 8P
   Evaluation Kit
Rev 1; 3/98
MAX2411A MAXIM-MAX2411A_1 Datasheet
96Kb / 6P
   Evaluation Kit
Rev 1; 2/98
MAX2685 MAXIM-MAX2685_1 Datasheet
162Kb / 6P
   Evaluation Kit
Rev 0; 7/99
More results


Html Pages

1 2


Datenblatt Download

Go To PDF Page


Link URL




Privatsphäre und Datenschutz
ALLDATASHEETDE.COM
War ALLDATASHEET hilfreich?  [ DONATE ] 

Über Alldatasheet   |   Werbung   |   Kontakt   |   Privatsphäre und Datenschutz   |   Linktausch   |   Hersteller
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com