![]() |
Datenblatt-Suchmaschine für elektronische Bauteile |
|
MC13077DW Datenblatt(PDF) 7 Page - Motorola, Inc |
|
MC13077DW Datenblatt(HTML) 7 Page - Motorola, Inc |
7 / 14 page ![]() MC13077 7 MOTOROLA ANALOG IC DEVICE DATA 1000 pF Figure 4. Versatility of the 4x fsc Oscillator Direct Drive of Oscillator with 4x fsc Source MC13077 8 9 150 p 220 1000 pF 4x fsc Drive (150 mV to 3.0 Vpp) MC13077 8 9 4x fsc Resonator Subcarrier Reference Input 1000 pF Oscillator Phase Lock with Resonator to Subcarrier Reference MC13077 8 9 MC13077 8 9 4x fsc Crystal 5–25 pF Oscillator Free Run with Crystal 4x fsc Crystal Oscillator Phase Lock with Crystal to Subcarrier Reference Subcarrier Reference Input (Pull–in Range of ± 400 Hz) fsc 5–25 pF 4X Subcarrier Oscillator To encode the color difference components, an accurate and reliable subcarrier source is required. The MC13077 has an on–chip single pin oscillator that will free–run with a 4x fsc crystal, phase–lock to an external subcarrier reference with a 4x fsc crystal or resonator, or be driven externally from a 4x fsc source. If the 4x fsc oscillator is going to be free run, the subcarrier input (Pin 9) should be grounded. If the 4x fsc oscillator is going to be phase–locked to an external subcarrier source, the external reference should be capacitor–coupled to Pin 9. If the 4x fsc oscillator is going to be driven externally, Pin 8 should be driven from a network that increases the impedance of the source at frequencies capable of producing off–frequency oscillations. The 4x fsc subcarrier source, thus being defined, makes it possible to produce accurate quadrature subcarriers for the modulators. The 4x source is internally divided by a ring counter to produce the quadrature subcarrier signals. These signals in turn are provided to the color difference modulators to produce the modulated chroma. The oscillator was designed so that if a crystal is chosen as the resonant element of the 4x oscillator, the crystal specifications would be common. Crystal specifications for an adequate crystal are shown in 1 Table 1. Crystal Specifications Frequency: 14.31818 MHz (NTSC) 17.734475 MHz (PAL) Mode: Fundamental Frequency Tolerance (@25 °C), 40 ppm Frequency Tolerance df/dfo (0 ° –70°C), 40 ppm Load Capacitance: 20 pF ESR: 50 Ω C1(Internal Series Capacitance), 15 mpF This crystal is a common variety and is specified as a parallel resonant. Burst Flag Decoding In order to encode to either NTSC or PAL compatibility, the MC13077 must first determine which is the intended standard. The MC13077 accomplishes this with an internal decode using the sync input and the output of the divide by 4 ring counter. Internally, the Sync separator circuitry provides an output that is sampled by the subcarrier signal from the ring counter. The result is an internal sync representative of externally input sync but synchronized to the internal subcarrier signal. This signal provides a reset for an internal 9–bit counter that provides divisions of the subcarrier signal from the ring counter at powers of 2 (i.e. 21, 22, 23,...29 = 512). The eighth bit of the counter gives the output, fsc ÷ 256. The decision to provide burst gate timing for PAL or NTSC is based upon the state of this output after one period of the horizontal sync. Figure 5 shows the relationship between the clock and the eighth bit of the counter. Triggering of the burst PAL flip–flop due to equalizing pulses is also inhibited by the decode circuitry. This is done by counting out beyond a half line interval before generating burst flag. If the MC13077 is encoding 525/60 component video to NTSC and the MC13077 is generating the burst flag, the start of burst will occur 18 counts after the leading edge of sync has been sampled, and will continue until nine cycles of burst have occurred. Since the reset pulse of the 9–bit counter has a resolution of 1.0/fsc, this implies that the start of burst will occur 5.17 ± 0.1397 µs after the leading edge of sync and also that the start (and end) of burst may differ by as much as 279.4 ns from line–to–line. If the MC13077 is encoding 625/50 to PA L, the subcarrier frequency will be 4.43361875 MHz and that implies a resolution of 225.5 ns for the burst position. For PAL encoding, 24 counts of the subcarrier are necessary before burst is initiated. So ten cycles of subcarrier will occur 5.53 ± 0.1128 µs after the leading edge of sync. After the timing of the burst gate is selected, the burst gate envelope is added to the color difference components. Another alternative to the internal determination of burst flag is the external input of burst flag. This allows the user to externally define the exact timing and duration of color burst. If external burst flag is available, it can be inserted at Pin 18. The threshold level is nominally VCC/2 and the input should not exceed VCC. Burst will begin when the leading edge of the burst flag input exceeds VCC/2 and will stop when it falls below VCC/2. If it is desired to disable the burst flag, Pin 18 can be pulled low. It is also possible to insert burst flag with the R–Y and B–Y components. This is done at the clamp pins with the respective color difference inputs with the internal burst flag generation disabled (Pin 18 grounded). |
Ähnliche Teilenummer - MC13077DW |
|
Ähnliche Beschreibung - MC13077DW |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |