Datenblatt-Suchmaschine für elektronische Bauteile |
|
LM211DR2G Datenblatt(PDF) 3 Page - ON Semiconductor |
|
LM211DR2G Datenblatt(HTML) 3 Page - ON Semiconductor |
3 / 10 page LM211, LM311 http://onsemi.com 3 ELECTRICAL CHARACTERISTICS (VCC = +15 V, VEE = −15 V, TA = 25°C, unless otherwise noted) Note 1 Characteristic Symbol LM211 LM311 Unit Min Typ Max Min Typ Max Input Offset Voltage (Note 3) VIO mV RS ≤ 50 kW, TA = +25°C − 0.7 3.0 − 2.0 7.5 RS ≤ 50 kW, Tlow ≤ TA ≤ Thigh* − − 4.0 − − 10 Input Offset Current (Note 3) TA = +25°C IIO − 1.7 10 − 1.7 50 nA Tlow ≤ TA ≤ Thigh* − − 20 − − 70 Input Bias Current TA = +25°C IIB − 45 100 − 45 250 nA Tlow ≤ TA ≤ Thigh* − − 150 − − 300 Voltage Gain AV 40 200 − 40 200 − V/mV Response Time (Note 4) − 200 − − 200 − ns Saturation Voltage VOL V VID ≤ −5.0 mV, IO = 50 mA, TA = 25°C − 0.75 1.5 − − − VID ≤−10 mV, IO = 50 mA, TA = 25°C − − − − 0.75 1.5 VCC ≥ 4.5 V, VEE = 0, Tlow ≤ TA ≤ Thigh* VID 6≤6.0 mV, Isink ≤ 8.0 mA − 0.23 0.4 − − − VID 6≤10 mV, Isink ≤ 8.0 mA − − − − 0.23 0.4 Strobe ”On” Current (Note 5) IS − 3.0 − − 3.0 − mA Output Leakage Current VID ≥ 5.0 mV, VO= 35 V, TA = 25°C, Istrobe= 3.0 mA − 0.2 10 − − − nA VID ≥ 10 mV, VO= 35 V, TA = 25°C, Istrobe= 3.0 mA − − − − 0.2 50 nA VID ≥ 5.0 mV, VO= 35 V, Tlow ≤ TA ≤ Thigh* − 0.1 0.5 − − − mA Input Voltage Range (Tlow ≤ TA ≤ Thigh*) VICR −14.5 −14.7 to 13.8 +13.0 −14.5 −14.7 to 13.8 +13.0 V Positive Supply Current ICC − +2.4 +6.0 − +2.4 +7.5 mA Negative Supply Current IEE − −1.3 −5.0 − −1.3 −5.0 mA * LM211: Tlow = −25°C, Thigh = +85°C LM311: Tlow = 0°C, Thigh = +70°C 1. Offset voltage, offset current and bias current specifications apply for a supply voltage range from a single 5.0 V supply up to ±15 V supplies. 2. This rating applies for ±15 V supplies. The positive input voltage limit is 30 V above the negative supply. The negative input voltage limit is equal to the negative supply voltage or 30 V below the positive supply, whichever is less. 3. The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a 1.0 mA load. Thus, these parameters define an error band and take into account the “worst case” effects of voltage gain and input impedance. 4. The response time specified is for a 100 mV input step with 5.0 mV overdrive. 5. Do not short the strobe pin to ground; it should be current driven at 3.0 mA to 5.0 mA. Figure 2. Circuit Schematic 8 7 1 4 VEE GND Output VCC 5.0k 200 600 3.0k 300 900 800 5.4k 1.3k 250 800 800 100 3.7k 730 340 3.7k 300 5 6 300 2 3 Inputs 1.3k 1.3k 1.3k Balance Balance/Strobe |
Ähnliche Teilenummer - LM211DR2G |
|
Ähnliche Beschreibung - LM211DR2G |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |