Datenblatt-Suchmaschine für elektronische Bauteile |
|
3966 Datenblatt(PDF) 6 Page - Allegro MicroSystems |
|
3966 Datenblatt(HTML) 6 Page - Allegro MicroSystems |
6 / 9 page 3966 DUAL FULL-BRIDGE PWM MOTOR DRIVER 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 6 Load Current Regulation. Due to internal logic and switching delays (td), the actual load current peak will be slightly higher than the ITRIP value. These delays, plus the blanking time, limit the minimum value the current control circuitry can regulate. To produce zero current in a winding, the ENABLE terminal should be held high, turning off all output drivers for that H-bridge. Logic Inputs. A logic high on the PHASE input results in current flowing from OUTA to OUTB of that H-bridge. A logic low on the PHASE input results in current flowing from OUTB to OUTA. An internally generated dead time (tcodt) of approximately 1 µs prevents cross-over current spikes that can occur when switching the PHASE input. A logic high on the ENABLE input turns off all four output drivers of that H-bridge. This results in a fast current decay through the internal ground clamp and flyback diodes. A logic low on the ENABLE input turns on the selected source and sink driver of that H-bridge. The ENABLE inputs can be pulse-width modulated for applications that require a fast current-decay PWM. If external current-sensing circuitry is used, the internal current-control logic can be disabled by connecting the RTCT terminal to ground. The REFERENCE input voltage is typically set with a resistor divider from VCC. This reference voltage is internally divided down by 4 to set up the current-com- parator trip-voltage threshold. The reference input voltage range is 0 to 2 V. Output Drivers. To minimize on-chip power dissipation, the sink drivers incorporate a Satlington structure. The Satlington output combines the low VCE(sat) features of a saturated transistor and the high peak-current capability of a Darlington (connected) transistor. A graph showing typical output saturation voltages as a function of output current is on the next page. Miscellaneous Information. Thermal protection circuitry turns off all output drivers should the junction temperature reach +165 °C (typical). This is intended only to protect the device from failures due to excessive junction temperatures and should not imply that output short circuits are permitted. Normal operation is resumed when the junction temperature has decreased about 15°C. The A3966 current control employs a fixed-fre- quency, variable duty cycle PWM technique. As a result, the current-control regulation may become unstable if the duty cycle exceeds 50%. To minimize current-sensing inaccuracies caused by ground trace IR drops, each current-sensing resistor should have a separate return to the ground terminal of the device. For low-value sense resistors, the I x R drops in the printed-wiring board can be significant and should be taken into account. The use of sockets should be avoided as their contact resistance can cause variations in the effective value of RS. The LOAD SUPPLY terminal, VBB, should be decoupled with an electrolytic capacitor (47 µF recom- mended) placed as close to the device as physically practical. To minimize the effect of system ground I x R drops on the logic and reference input signals, the system ground should have a low-resistance return to the load supply voltage. The frequency of the clock oscillator will determine the amount of ripple current. A lower frequency will result in higher current ripple, but reduced heating in the motor and driver IC due to a corresponding decrease in hysteretic core losses and switching losses respectively. A higher frequency will reduce ripple current, but will increase switching losses and EMI. FUNCTIONAL DESCRIPTION (continued) |
Ähnliche Teilenummer - 3966_03 |
|
Ähnliche Beschreibung - 3966_03 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |