Datenblatt-Suchmaschine für elektronische Bauteile |
|
ST24LC21BM1TR Datenblatt(PDF) 5 Page - STMicroelectronics |
|
ST24LC21BM1TR Datenblatt(HTML) 5 Page - STMicroelectronics |
5 / 22 page A byte is clocked out (on SDA pin) with nine clock pulses on VCLK: 8 clock pulses for the data byte and one extra clock pulse for a Don’t Care bit. As long as the SCL pin is held high, each byte of the memory array is transmitted serially on the SDA pin with an automatic address increment. When the last byte is transmitted, the address counter will roll-over to location 00h. I2C Bidirectional Mode The ST24xy21 can be switched from Transmit Only mode to I2C Bidirectional mode by applying a valid high to low transition on the SCL pin (see Figure 4). – When the ST24LC21B (or the ST24FC21 or the ST24FC21B) is in the I2C Bidirectional mode, the VCLK input (pin 7) enables (or inhib- its) the execution of any write instruction: if VCLK = 1, write instructions are executed; if VCLK = 0, write instructions are not executed. – When the ST24LW21 (or the ST24FW21) is in the I2C Bidirectional mode, the Write Control (WC on pin 3) input enables (or inhibits) the execution of any write instruction: if WC = 1, write instructions are executed;if WC = 0, write instructions are not executed. The ST24xy21 is compatible with the I2C standard, two wire serial interface which uses a bidirectional data bus and serial clock. The ST24xy21 carries a built-in 4 bit, unique device identification code (1010) named Device Select code corresponding to the I2C bus definition. The ST24LC21B carries a unique device identification code (1010.0000 RW) named Device Select code corresponding to the I2C bus definition. The ST24xy21 behaves as a slave device in the I2C protocol with all memory operations synchro- nized by the serial clock SCL. Read and write operations are initiated by a START condition gen- erated by the bus master. The START condition is followed by a stream of 7 bits, plus one read/write bit and terminated by an acknowledge bit. When data is written into the memory, the ST24xy21 responds to the 8 bits received by as- serting an acknowledge bit during the 9th bit time. When data is read by the bus master, it must acknowledge the receipt of the data bytes in the same way. Data transfers are terminated with a STOP condition (see READ and WRITE descrip- tions in the following pages). Power On Reset: VCC lock out write protect In order to prevent data corruption and inadvertent write operations during power up, a Power On Reset (POR) circuit is implemented. Until the VCC voltage has reached the POR threshold value, the internal reset is active, all operations are disabled and the device will not respond to any command. In the same way, when VCC drops down from the operating voltage to below the POR threshold value, all operations are disabled and the device will not respond to any command. A stable VCC must be applied before applying any logic signal. Error Recovery Modes available in the ST24FC21, ST24FC21B and the ST24FW21 AI01892 SCL SDA VCLK Transmit Only Mode 1 2 89 MSB ACK START CONDITION - Temporary Bi-Directional Mode (ST24FC21 and ST24FW21) - Locked Bi-Directional Mode (ST24LC21B and ST24LW21) - Locked Bi-Directional Mode (ST24FC21 and ST24FW21) Figure 4. Transition from Transmit Only (DDC1) to Bi-directional (DDC2B) Mode Waveforms 5/22 ST24LC21B, ST24LW21, ST24FC21, ST24FC21B, ST24FW21 |
Ähnliche Teilenummer - ST24LC21BM1TR |
|
Ähnliche Beschreibung - ST24LC21BM1TR |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |