Datenblatt-Suchmaschine für elektronische Bauteile |
|
MC34712 Datenblatt(PDF) 11 Page - Freescale Semiconductor, Inc |
|
MC34712 Datenblatt(HTML) 11 Page - Freescale Semiconductor, Inc |
11 / 24 page Analog Integrated Circuit Device Data Freescale Semiconductor 11 34712 FUNCTIONAL DESCRIPTION FUNCTIONAL PIN DESCRIPTION INTERNAL SUPPLY VOLTAGE OUTPUT (VDDI) This is the output of the internal bias voltage regulator. Connect a 1.0 µF, 6.0 V low ESR ceramic filter capacitor between this pin and the GND pin. Filtering any spikes on this output is essential to the internal circuitry stable operation. OUTPUT VOLTAGE DISCHARGE PATH (VOUT) Output voltage of the Buck Converter is connected to this pin. it only serves as the output discharge path once the SD signal is asserted. ERROR AMPLIFIER INVERTING INPUT (INV) Buck converter error amplifier inverting input. Connect the VTT voltage directly to this pin. COMPENSATION INPUT (COMP) Buck converter external compensation network connects to this pin. Use a type III compensation network. INPUT SUPPLY VOLTAGE (VIN) IC power supply input voltage. Input filtering is required for the device to operate properly. POWER GROUND (PGND) Buck converter and discharge MOSFETs power ground. It is the source of the buck converter low side power MOSFET. SWITCHING NODE (SW) Buck converter switching node. This pin is connected to the output inductor. POWER INPUT VOLTAGE (PVIN) Buck converter power input voltage. This is the drain of the buck converter high side power MOSFET. BOOTSTRAP INPUT (BOOT) Bootstrap capacitor input pin. Connect a capacitor (as discussed on page 19) between this pin and the SW pin to enhance the gate of the high side Power MOSFET during switching. SHUTDOWN INPUT (SD) If this pin is tied to the GND pin, the device will be in Shutdown mode. If left unconnected or tied to the VIN pin, the device will be in Normal mode. The pin has an internal pull- up of 1.5 M Ω. This input accepts the S5 (Suspend-To-Disk) control signal. STANDBY INPUT (STBY) If this pin is tied to the GND pin, the device will be in Standby mode. If left unconnected or tied to the VIN pin, the device will be in Normal mode. The pin has an internal pull- up of 1.5 M Ω. This input accepts the S3 (Suspend-To-RAM) control signal. POWER GOOD OUTPUT SIGNAL (PG) This is an active low open drain output that is used to report the status of the device to a host. This output activates after a successful power up sequence and stays active as long as the device is in normal operation and is not experiencing any faults. This output activates after a 10 ms delay and must be pulled up by an external resistor to a supply voltage (e.g.,VIN.). |
Ähnliche Teilenummer - MC34712 |
|
Ähnliche Beschreibung - MC34712 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |