Datenblatt-Suchmaschine für elektronische Bauteile |
|
TS2507 Datenblatt(PDF) 4 Page - Taiwan Semiconductor Company, Ltd |
|
TS2507 Datenblatt(HTML) 4 Page - Taiwan Semiconductor Company, Ltd |
4 / 9 page TS2507 0.5A / 330KHz PWM Buck Controller 4/9 Version: A07 Function Descriptions PWM Control The TS2507 integrates Pulse-Width-Modulation (PWM) control circuit into a single chip. the pulse width varies in a range from 0 to 100%, according to the load current. The ripple voltage produced by the switching can easily be removed through a filter because the switching frequency remains constant. Therefore, these controllers provide a low-ripple power over broad ranges of input voltage and load current. RDS(ON) Current Limiting The current limit threshold is setting by the external resistor (R3) connecting from VCC supply to OCSET pin. The internal 110uA sink current crossing the resistor sets the voltage at pin of OCSET. When the PWM voltage is less than the voltage at OCSET, an over-current condition is triggered. Please refer to the formula for setting the current limit value (Normally, The ISW(MAX) setting more than IOUT 1A) Example: ISW=(110uA * 1.8k + 0.11) / 50mΩ (TSM9435CS) = 6.16A Setting the Output Voltage Application circuit item shows the basic application circuit with TS2507 adjustable output version. The external resistor sets the output voltage according to the following equation: Table 1: Resistor select for output voltage setting VOUT R2 R1 1.3K 6.8K 5V 5.6K 30K 1.5K 4.7K 3.3V 5.6K 18K 2.2K 4.7K 2.5V 5.6K 12K 1.8V 1.2K 1.5K 1.5V 2.2K 2K 1.2V 2K 1K 1V 2K 0.5K Input Capacitor Selection The input capacitor reduces the surge current drawn from the input and switching noise from the device. The input capacitor impedance at the switching frequency shall be less than input source impedance to prevent high frequency switching current passing to the input. A low ESR input capacitor sized for maximum RMS current must be used. The capacitor voltage rating should be at least 1.5 times greater than the input voltage, and often much higher voltage ratings are needed to satisfy. Output Capacitor Selection The output capacitor is required to keep the output voltage ripple small and to ensure regulation loop stability. The output capacitor must have low impedance at the switching frequency. A low ESR capacitor sized for maximum RMS current must be used. the low ESR requirements needed for low output ripple voltage. The capacitor voltage rating should be at least 1.5 times greater than the input voltage, and often much higher voltage ratings are needed to satisfy. |
Ähnliche Teilenummer - TS2507 |
|
Ähnliche Beschreibung - TS2507 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |