Datenblatt-Suchmaschine für elektronische Bauteile
  German  ▼
ALLDATASHEETDE.COM

X  

ISL1903EVAL2Z Datenblatt(PDF) 6 Page - Intersil Corporation

Teilenummer ISL1903EVAL2Z
Bauteilbeschribung  Dimmable Buck LED Driver - AC Mains or DC Input LED Driver
Download  19 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Hersteller  INTERSIL [Intersil Corporation]
Direct Link  http://www.intersil.com/cda/home
Logo INTERSIL - Intersil Corporation

ISL1903EVAL2Z Datenblatt(HTML) 6 Page - Intersil Corporation

Back Button ISL1903EVAL2Z Datasheet HTML 2Page - Intersil Corporation ISL1903EVAL2Z Datasheet HTML 3Page - Intersil Corporation ISL1903EVAL2Z Datasheet HTML 4Page - Intersil Corporation ISL1903EVAL2Z Datasheet HTML 5Page - Intersil Corporation ISL1903EVAL2Z Datasheet HTML 6Page - Intersil Corporation ISL1903EVAL2Z Datasheet HTML 7Page - Intersil Corporation ISL1903EVAL2Z Datasheet HTML 8Page - Intersil Corporation ISL1903EVAL2Z Datasheet HTML 9Page - Intersil Corporation ISL1903EVAL2Z Datasheet HTML 10Page - Intersil Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 6 / 19 page
background image
ISL1903
6
FN8285.1
September 20, 2012
Pin Configuration
ISL1903
(16 LD QSOP)
TOP VIEW
CS+
DHC
OFFREF PWMOUT
VREF
OUT
VDD
OC
OVP
1
2
4
3
5
6
7
8
AC
IOUT
RAMP
9
10
11
12
13
14
15
16
GND
FB
DELADJ
VERR
Pin Descriptions
PIN #
SYMBOL
DESCRIPTION
1
VDD
VDD is the power connection for the IC. To optimize noise immunity, bypass VDD to GND with a ceramic capacitor as close to
the VDD and GND pins as possible.
2
OFFREF
Sets the reference level to disable the driver at light loading. The turn-off reference can be set at any level between 0 and 0.6V,
corresponding to 0 to 100% of output loading. This feature is normally used in triac-based wall dimmer applications to disable
the output before the dimmer becomes unstable due to insufficient holding current.
3
VREF
The 5.40V reference voltage output having ±100 mV tolerance over line, load and operating temperature. Bypass to GND with
a 0.1µF to 3.3µF low ESR capacitor.
4
IOUT
A voltage signal proportional to the peak switching current used to determine the inductor current.
5
CS+
The input for the CrCM current sense circuit. This input monitors the winding current or voltage to determine the critical
conduction operating point.
6
OC
The input to the load current sensing circuitry and the peak overcurrent comparator. The signal is sampled at the peak current
level for each switching cycle, amplified, and output on IOUT as a DC signal. It must be scaled before application to the FB pin
of the error amplifier (EA). The overcurrent comparator threshold is set at 600mV nominal. Peak OCP performs cycle-by-cycle
over current protection. OCP includes leading-edge-blanking (LEB), which blocks the signal at the beginning of the OUT pulse
for the duration of the blanking period and when the OUT pulse is low.
7
FB
FB is the inverting input to the error amplifier (EA). The feedback signal from IOUT, after being scaled and filtered, is applied
to the error amplifier.
8
DELADJ
Sets delay before a new switching cycles starts. This adjustment allows the user to delay the next switching cycle until the
switching FET drain-source voltage reaches a minimum value to allow quasi-ZVS (Zero Voltage Switching) operation. A resistor
to ground programs the delay. Pulling DELADJ to VREF disables the CrCM oscillator.
9
VERR
Output of the error amplifiers and the control voltage input to the inverting input of the PWM comparator. VERR cannot source
current and requires an external pull-up resistor to VREF.
10
RAMP
This is the input for the sawtooth waveform for the PWM comparator. Using an RC from VREF, a sawtooth waveform is created
for use by the PWM. It is compared to the error amplifier output, Verr, to create the PWM control signal. The RAMP pin is shorted
to GND at the termination of the PWM signal.
11
OVP
Input to detect an overvoltage (OV) condition on the output. Since the control variable is output current, a fault that results in
an open circuit will cause excessive output voltage. The circuit hysteresis is a switched current source that is active when the
OV threshold is exceeded.
12
AC
Input to sense AC voltage presence and amplitude. A resistor divider from the main FET drain and circuit ground or from an
auxiliary winding on the transformer/inductor is used to detect the AC voltage.
13
GND
Signal and power ground connections for this device. Due to high peak currents and high frequency operation, a low impedance
layout is necessary. Ground planes and short traces are highly recommended.
14
DHC
An open drain FET used to load the input voltage to pre-load a triac-based dimmer so that adequate holding current is
maintained.


Ähnliche Teilenummer - ISL1903EVAL2Z

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
Renesas Technology Corp
ISL1903EVAL2Z RENESAS-ISL1903EVAL2Z Datasheet
888Kb / 19P
   Dimmable Buck LED Driver - AC Mains or DC Input LED Driver
More results

Ähnliche Beschreibung - ISL1903EVAL2Z

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
Renesas Technology Corp
ISL1903 RENESAS-ISL1903 Datasheet
888Kb / 19P
   Dimmable Buck LED Driver - AC Mains or DC Input LED Driver
logo
Bright Power Semiconduc...
BP5132HC BPS-BP5132HC Datasheet
494Kb / 2P
   Mains Dimmable Liner LED Driver
BP5152HC BPS-BP5152HC Datasheet
497Kb / 2P
   Mains Dimmable Liner LED Driver
logo
Shenzhen Huazhimei Semi...
HM9912 HMSEMI-HM9912 Datasheet
601Kb / 5P
   DC or AC input LED driver
logo
NXP Semiconductors
AN10952 PHILIPS-AN10952_15 Datasheet
265Kb / 40P
   SSL2103 flexible, mains-dimmable LED driver
Rev. 1-24 December 2010
logo
Diodes Incorporated
AL16937 DIODES-AL16937 Datasheet
327Kb / 15P
   BUCK DIMMABLE LED DRIVER
logo
Intersil Corporation
ISL1902 INTERSIL-ISL1902 Datasheet
872Kb / 25P
   Full-Featured, Dimmable AC Mains LED Driver with PFC
logo
Renesas Technology Corp
ISL1902 RENESAS-ISL1902 Datasheet
1Mb / 25P
   Full-Featured, Dimmable AC Mains LED Driver with PFC
logo
NXP Semiconductors
SSL2102 NXP-SSL2102 Datasheet
116Kb / 21P
   Mains LED driver IC for dimmable LED lighting
Rev. 01-29 June 2009
AN10754 PHILIPS-AN10754_15 Datasheet
214Kb / 37P
   SSL2101 and SSL2102 dimmable mains LED driver
Rev. 4.1-5 November 2012
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19


Datenblatt Download

Go To PDF Page


Link URL




Privatsphäre und Datenschutz
ALLDATASHEETDE.COM
War ALLDATASHEET hilfreich?  [ DONATE ] 

Über Alldatasheet   |   Werbung   |   Kontakt   |   Privatsphäre und Datenschutz   |   Linktausch   |   Hersteller
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com