Datenblatt-Suchmaschine für elektronische Bauteile
  German  ▼
ALLDATASHEETDE.COM

X  

AD883B Datenblatt(PDF) 5 Page - Analog Devices

Teilenummer AD883B
Bauteilbeschribung  Low Cost 10-Bit Monolithic D/A Converter
Download  8 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Hersteller  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

AD883B Datenblatt(HTML) 5 Page - Analog Devices

  AD883B Datasheet HTML 1Page - Analog Devices AD883B Datasheet HTML 2Page - Analog Devices AD883B Datasheet HTML 3Page - Analog Devices AD883B Datasheet HTML 4Page - Analog Devices AD883B Datasheet HTML 5Page - Analog Devices AD883B Datasheet HTML 6Page - Analog Devices AD883B Datasheet HTML 7Page - Analog Devices AD883B Datasheet HTML 8Page - Analog Devices  
Zoom Inzoom in Zoom Outzoom out
 5 / 8 page
background image
AD561
–5–
REV. A
UNIPOLAR CONFIGURATION
This configuration, shown in Figure 2, will provide a unipolar
0 V to +10 V output range.
STEP I . . . ZERO ADJUST
Turn all bits OFF and adjust op amp trimmer, R1, until the
output reads 0.000 volts (1 LSB = 9.76 mV).
STEP 11. . . GAIN ADJUST
Turn all bits ON and adjust 50
Ω gain trimmer, R
2, until the
output is 9.990 volts. (Full scale is adjusted to 1 LSB less than
nominal full scale of 10.000 volts.) If a 10.23 V full scale is desired
(exactly 10 mV/bit), insert a 120
Ω resistor in series with R
2.
BIPOLAR CONFIGURATION
This configuration, shown in Figure 3, will provide a bipolar
output voltage from –5.000 to +4.990 volts, with positive full
scale occurring with all bits ON (all 1s).
STEP 1. . . ZERO ADJUST
Turn ON MSB only, turn OFF all other bits. Adjust 50
trimmer R3, to give 0.000 output volts. For maximum resolution
a 120
Ω resistor may be placed in parallel with R
3.
STEP 11. . . GAIN ADJUST
Turn OFF all bits, adjust 50
Ω gain trimmer to give a reading of
–5.000 volts.
Please note that it is not necessary to trim the op amp to obtain
full accuracy at room temperature. In most bipolar situations,
the op amp trimmer is unnecessary unless the untrimmed offset
drift of the op amp is excessive.
10 VOLT BUFFERED BIPOLAR OUTPUT
The AD561 can also be connected for a
±10 volt bipolar range
with an additional external resistor as shown in Figure 4. A
larger value trimmer is required to compensate for tolerance in
the thin film resistors, which are trimmed to match the full-scale
current. For best full scale temperature coefficient performance,
the external resistors should have a TC of –50 ppm/
°C.
CIRCUIT DESCRIPTION
A simplified schematic with the essential circuit features of the
AD561 is shown in Figure 5. The voltage reference, CR1, is a
buried Zener (or subsurface breakdown diode). This device
exhibits far better all-around performance than the NPN base-
emitter reverse-breakdown diode (surface Zener), which is in
nearly universal use in integrated circuits as a voltage reference.
Greatly improved long-term stability and lower noise are the
major benefits the buried Zener derives from isolating the
breakdown point from surface stress and mobile oxide charge
effects. The nominal 7.5 volt device (including temperature
compensation circuitry) is driven by a current source to the
negative supply so the positive supply can be allowed to drop as
low as 4.5 volts. The temperature coefficient of each diode is
individually determined; this data is then used to laser trim a
compensating circuit to balance the overall TC to zero. The
typical resulting TC is 0 to
±15 ppm/°C. The negative reference
level is inverted and scaled by A1 to give a +2.5 volt reference,
which can be driven by the low positive supply. The AD561,
packaged in the 16-pin DIP, has the +2.5 volt reference (REF
OUT) connected directly to the input of the control amplifier
(REF IN). The buffered reference is not directly available
externally except through the 2.5 k
Ω bipolar offset resistor.
The 2.5 k
Ω scaling resistor and control amplifier A
2 then force a
1 mA reference current to flow through reference transistor Q1,
which has a relative emitter area of 8A. This is accomplished by
forcing the bottom of the ladder to the proper voltage. Since Q1
and Q2 have equal emitter areas and equal 5 k
Ω emitter resistors,
Q2 also carries 1 mA. The ladder voltage drop constrains Q7
(with area 4A) to carry only 0.5 mA; Q8 carries 0.25 mA, etc.
The first four significant bit cells are exactly scaled in emitter
area to match Q1 for optimum VBE and VBE drift match, as well
as for beta match. These effects are insignificant for the lower
order bits, which account for a total of only 1/16 of full scale.
However, the 18 mV VBE difference between two matched
transistors carrying emitter currents in a ratio of 2:1 must be
corrected. This is achieved by forcing 120
µA through the
150
Ω interbase resistors. These resistors, and the R-2R ladder
resistors, are actively laser-trimmed at the wafer level to bring
total device accuracy to better than 1/4 LSB. Sufficient ratio
accuracy in the last two bits is obtained by simple emitter area
Figure 2. 0 V to +10 V Unipolar Voltage Output
Figure 3.
±5 V Buffered Bipolar Voltage Output
Figure 4.
±10 V Buffered Voltage Output


Ähnliche Teilenummer - AD883B

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
Analog Devices
AD883B AD-AD883B Datasheet
464Kb / 14P
   Software Programmable Gain Amplifier
REV. D
AD883B AD-AD883B Datasheet
571Kb / 16P
   Low Cost, Low Power Instrumentation Amplifier
REV. E
AD883B AD-AD883B Datasheet
136Kb / 7P
   Internally Trimmed Integrated Circuit Multiplier
REV. B
AD883B AD-AD883B Datasheet
691Kb / 15P
   Precision Instrumentation Amplifier
REV. C
AD883B AD-AD883B Datasheet
159Kb / 12P
   Internally Trimmed Precision IC Multiplier
REV. B
More results

Ähnliche Beschreibung - AD883B

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
Analog Devices
AD561 AD-AD561_17 Datasheet
623Kb / 5P
   LOW COST, 10-BIT MONOLITHIC D/A CONVERTER
AD561 AD-AD561_15 Datasheet
213Kb / 8P
   Low Cost 10-Bit Monolithic D/A Converter
REV. A
AD561SD-883B AD-AD561SD-883B Datasheet
524Kb / 6P
   Low Cost 10-Bit Monolithic D/A Converter
REV. G
logo
Intersil Corporation
HI-DAC80V INTERSIL-HI-DAC80V_01 Datasheet
92Kb / 8P
   12-Bit, Low Cost, Monolithic D/A Converter
logo
Renesas Technology Corp
HI-DAC80V RENESAS-HI-DAC80V Datasheet
483Kb / 8P
   12-Bit, Low Cost, Monolithic D/A Converter
logo
Analog Devices
AD6012 AD-AD6012_15 Datasheet
2Mb / 6P
   LOW COST MONOLITHIC 12 BIT D/A CONVERTER
logo
Maxim Integrated Produc...
MX7533 MAXIM-MX7533 Datasheet
429Kb / 8P
   CMOS Low Cost 10 Bit Multiplying D/A Converter
Rev 1a; 7/95
logo
List of Unclassifed Man...
ZN429E8 ETC-ZN429E8 Datasheet
195Kb / 7P
   LOW COST 8-BIT D-A CONVERTER
logo
Intersil Corporation
HI-DAC80V INTERSIL-HI-DAC80V Datasheet
68Kb / 7P
   12-Bit, Low Cost, Monolithic D/A Converters
August 1997
logo
Analog Devices
AD773 AD-AD773_15 Datasheet
4Mb / 16P
   10 BIT 18 MSPS MONOLITHIC A/D CONVERTER
REV. 0
More results


Html Pages

1 2 3 4 5 6 7 8


Datenblatt Download

Go To PDF Page


Link URL




Privatsphäre und Datenschutz
ALLDATASHEETDE.COM
War ALLDATASHEET hilfreich?  [ DONATE ] 

Über Alldatasheet   |   Werbung   |   Kontakt   |   Privatsphäre und Datenschutz   |   Linktausch   |   Hersteller
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com