Datenblatt-Suchmaschine für elektronische Bauteile
  German  ▼
ALLDATASHEETDE.COM

X  

ADM1021AARQ-REEL Datenblatt(PDF) 8 Page - Analog Devices

Teilenummer ADM1021AARQ-REEL
Bauteilbeschribung  Low-Cost Microprocessor System Temperature Monitor
Download  16 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Hersteller  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

ADM1021AARQ-REEL Datenblatt(HTML) 8 Page - Analog Devices

Back Button ADM1021AARQ-REEL Datasheet HTML 4Page - Analog Devices ADM1021AARQ-REEL Datasheet HTML 5Page - Analog Devices ADM1021AARQ-REEL Datasheet HTML 6Page - Analog Devices ADM1021AARQ-REEL Datasheet HTML 7Page - Analog Devices ADM1021AARQ-REEL Datasheet HTML 8Page - Analog Devices ADM1021AARQ-REEL Datasheet HTML 9Page - Analog Devices ADM1021AARQ-REEL Datasheet HTML 10Page - Analog Devices ADM1021AARQ-REEL Datasheet HTML 11Page - Analog Devices ADM1021AARQ-REEL Datasheet HTML 12Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 8 / 16 page
background image
ADM1021A
–8–
REV. D
The
ALERT interrupt latch is not reset by reading the Status
Register, but will be reset when the
ALERT output has been
serviced by the master reading the device address, provided the
error condition has gone away and the Status Register flag bits
have been reset.
Configuration Register
Two bits of the configuration register are used. If Bit 6 is 0, which
is the power-on default, the device is in operating mode with the
ADC converting. If Bit 6 is set to 1, the device is in standby
mode and the ADC does not convert. Standby mode can also
be selected by taking the
STBY pin low. In standby mode the val-
ues stored in the Remote and Local Temperature Registers remain
at the value they were when the part was placed in standby.
Bit 7 of the configuration register is used to mask the
ALERT out-
put. If Bit 7 is 0, which is the power-on default, the
ALERT output
is enabled. If Bit 7 is set to 1, the
ALERT output is disabled.
Table IV. Configuration Register Bit Assignments
Power-On
Bit
Name
Function
Default
7
MASK1
0 =
ALERT Enabled
0
1 =
ALERT Masked
6
RUN/STOP
0 = Run
0
1 = Standby
5–0
Reserved
0
Conversion Rate Register
The lowest three bits of this register are used to program the con-
version rate by dividing the ADC clock by 1, 2, 4, 8, 16, 32, 64,
or 128, to give conversion times from 125 ms (Code 07h) to 16
seconds (Code 00h). This register can be written to and read back
over the SMBus. The higher five bits of this register are unused
and must be set to zero. Use of slower conversion times greatly
reduces the device power consumption, as shown in Table V.
Table V. Conversion Rate Register Codes
Average Supply Current
Data
Conversion/sec
µA Typ at V
CC = 3.3 V
00h
0.0625
150
01h
0.125
150
02h
0.25
150
03h
0.5
150
04h
1
150
05h
2
150
06h
4
160
07h
8
180
08h to FFh
Reserved
Limit Registers
The ADM1021A has four limit registers to store local and remote,
high and low temperature limits. These registers can be written
to and read back over the SMBus. The high limit registers
perform a > comparison while the low limit registers perform a
< comparison. For example, if the high limit register is pro-
grammed as a limit of 80
°C, measuring 81°C will result in an
alarm condition. Even though the temperature measurement
range is from 0 to 127
°C, it is possible to program the limit
register with negative values. This is for backwards-compatibility
with the ADM1021.
One-Shot Register
The one-shot register is used to initiate a single conversion and
comparison cycle when the ADM1021A is in standby mode,
after which the device returns to standby. This is not a data
register as such and it is the write operation that causes the one-
shot conversion. The data written to this address is irrelevant and
is not stored.
SERIAL BUS INTERFACE
Control of the ADM1021A is carried out via the serial bus. The
ADM1021A is connected to this bus as a slave device, under the
control of a master device. Note that the SMBus and SCL pins
are three-stated when the ADM1021A is powered down and will
not pull down the SMBus.
ADDRESS PINS
In general, every SMBus device has a 7-bit device address (except
for some devices that have extended, 10-bit addresses). When
the master device sends a device address over the bus, the slave
device with that address will respond. The ADM1021A has two
address pins, ADD0 and ADD1, to allow selection of the device
address, so that several ADM1021As can be used on the same
bus, and/or to avoid conflict with other devices. Although only
two address pins are provided, these are three-state, and can be
grounded, left unconnected, or tied to VDD, so that a total of
nine different addresses are possible, as shown in Table VI.
It should be noted that the state of the address pins is only sampled
at power-up, so changing them after power-up will have no effect.
Table VI. Device Addresses
ADD0
ADD1
Device Address
00
0011 000
0NC
0011 001
01
0011 010
NC
0
0101 001
NC
NC
0101 010
NC
1
0101 011
10
1001 100
1NC
1001 101
11
1001 110
ADD0, ADD1 sampled at power-up only.
The serial bus protocol operates as follows:
1. The master initiates data transfer by establishing a START
condition, defined as a high-to-low transition on the serial
data line SDATA, while the serial clock line SCLK remains
high. This indicates that an address/data stream will follow.
All slave peripherals connected to the serial bus respond to
the START condition and shift in the next eight bits, consisting
of a 7-bit address (MSB first) plus an R/
W bit, which deter-
mines the direction of the data transfer, i.e., whether data
will be written to or read from the slave device.
The peripheral whose address corresponds to the transmitted
address responds by pulling the data line low during the low
period before the ninth clock pulse, known as the Acknowl-
edge Bit. All other devices on the bus now remain idle while
the selected device waits for data to be read from or written
to it. If the R/
W bit is a 0, the master will write to the slave
device. If the R/
W bit is a 1, the master will read from the
slave device.


Ähnliche Teilenummer - ADM1021AARQ-REEL

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
ON Semiconductor
ADM1021AARQZ ONSEMI-ADM1021AARQZ Datasheet
158Kb / 15P
   Low Cost Microprocessor System Temperature Monitor Microcomputer
June, 2010 ??Rev. 8
ADM1021AARQZ-R ONSEMI-ADM1021AARQZ-R Datasheet
158Kb / 15P
   Low Cost Microprocessor System Temperature Monitor Microcomputer
June, 2010 ??Rev. 8
ADM1021AARQZ-R ONSEMI-ADM1021AARQZ-R Datasheet
240Kb / 16P
   Low Cost Microprocessor System Temperature Monitor Microcomputer
July, 2012 ??Rev. 9
ADM1021AARQZ-R7 ONSEMI-ADM1021AARQZ-R7 Datasheet
158Kb / 15P
   Low Cost Microprocessor System Temperature Monitor Microcomputer
June, 2010 ??Rev. 8
More results

Ähnliche Beschreibung - ADM1021AARQ-REEL

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
Analog Devices
ADM1021 AD-ADM1021 Datasheet
139Kb / 12P
   Low Cost Microprocessor System Temperature Monitor
REV. 0
logo
ON Semiconductor
ADM1021A ONSEMI-ADM1021A_12 Datasheet
240Kb / 16P
   Low Cost Microprocessor System Temperature Monitor Microcomputer
July, 2012 ??Rev. 9
ADM1021A ONSEMI-ADM1021A Datasheet
158Kb / 15P
   Low Cost Microprocessor System Temperature Monitor Microcomputer
June, 2010 ??Rev. 8
NCT210 ONSEMI-NCT210 Datasheet
197Kb / 16P
   Low Cost Microprocessor System Temperature Monitor Microcomputer
September, 2012 ??Rev. 2
logo
Analog Devices
ADM9240 AD-ADM9240 Datasheet
280Kb / 22P
   Low Cost Microprocessor System Hardware Monitor
REV. 0
logo
ON Semiconductor
ADM9240 ONSEMI-ADM9240 Datasheet
5Mb / 22P
   Low Cost Microprocessor System Hardware Monitor
May 2010 - Rev.2
logo
Analog Devices
ADM9240ARU-REEL AD-ADM9240ARU-REEL Datasheet
288Kb / 22P
   Low Cost Microprocessor System Hardware Monitor
REV. 0
ADM1020 AD-ADM1020 Datasheet
132Kb / 12P
   8-Lead, Low-Cost, System Temperature Monitor
REV. 0
EVAL-ADM1023 AD-EVAL-ADM1023 Datasheet
292Kb / 12P
   Evaluation Board for Microprocessor System Temperature Monitor
REV. A 11/10/99
EVAL-ADM1022 AD-EVAL-ADM1022 Datasheet
346Kb / 14P
   Evaluation Board for Microprocessor System Temperature Monitor
REV. B
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16


Datenblatt Download

Go To PDF Page


Link URL




Privatsphäre und Datenschutz
ALLDATASHEETDE.COM
War ALLDATASHEET hilfreich?  [ DONATE ] 

Über Alldatasheet   |   Werbung   |   Kontakt   |   Privatsphäre und Datenschutz   |   Linktausch   |   Hersteller
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com