Datenblatt-Suchmaschine für elektronische Bauteile |
|
ISL22316WFU10Z Datenblatt(PDF) 6 Page - Intersil Corporation |
|
ISL22316WFU10Z Datenblatt(HTML) 6 Page - Intersil Corporation |
6 / 16 page 6 FN6186.3 August 14, 2015 NOTES: 5. Typical values are for TA = +25°C and 3.3V supply voltage. 6. LSB: [V(RW)127 – V(RW)0]/127. V(RW)127 and V(RW)0 are V(RW) for the DCP register set to 7F hex and 00 hex respectively. LSB is the incremental voltage when changing from one tap to an adjacent tap. 7. ZS error = V(RW)0/LSB. 8. FS error = [V(RW)127 – VCC]/LSB. 9. DNL = [V(RW)i – V(RW)i-1]/LSB-1, for i = 1 to 127. i is the DCP register setting. 10. INL = [V(RW)i – (i • LSB) – V(RW)0]/LSB for i = 1 to 127 11. for i = 16 to 127 decimal, T = -40°C to +125°C. Max( ) is the maximum value of the wiper voltage and Min ( ) is the minimum value of the wiper voltage over the temperature range. 12. MI = |RW127 – RW0|/127. MI is a minimum increment. RW127 and RW0 are the measured resistances for the DCP register set to 7F hex and 00 hex respectively. 13. Roffset = RW0/MI, when measuring between RW and RL. Roffset = RW127/MI, when measuring between RW and RH. 14. RDNL = (RWi – RWi-1)/MI -1, for i = 16 to 127. 15. RINL = [RWi – (MI • i) – RW0]/MI, for i = 16 to 127. 16. for i = 16 to 127, T = -40°C to +125°C. Max() is the maximum value of the resistance and Min () is the minimum value of the resistance over the temperature range. 17. tWC is the time from a valid STOP condition at the end of a Write sequence of I2C serial interface, to the end of the self-timed internal non-volatile write cycle. 18. Limits should be considered typical and are not production tested. 19. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. Rpu SDA and SCL Bus Pull-up Resistor Off-chip Maximum is determined by tR and tF For Cb = 400pF, max is about 2k ~2.5k For Cb = 40pF, max is about 15k ~20k 1k tSU:A A1 and A0 Setup Time Before START condition 600 ns tHD:A A1 and A0 Hold Time After STOP condition 600 ns Operating Specifications Over the recommended operating conditions, unless otherwise specified. (Continued) SYMBOL PARAMETER TEST CONDITIONS MIN (Note 19) TYP (Note 5) MAX (Note 19) UNIT TCV Max V RW i Min V RW i – Max V RW i Min V RW i + 2 ---------------------------------------------------------------------------------------------- 106 +165°C --------------------- = TCR Max Ri Min Ri – Max Ri Min Ri + 2 ---------------------------------------------------------------- 10 6 +165°C --------------------- = ISL22316 |
Ähnliche Teilenummer - ISL22316WFU10Z |
|
Ähnliche Beschreibung - ISL22316WFU10Z |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |