Datenblatt-Suchmaschine für elektronische Bauteile |
|
ML4805CS Datenblatt(PDF) 9 Page - Micro Linear Corporation |
|
ML4805CS Datenblatt(HTML) 9 Page - Micro Linear Corporation |
9 / 13 page ML4805 9 operating frequency can typically be approximated by: f t OSC RAMP = 1 (5) EXAMPLE: For the application circuit shown in the data sheet, with the oscillator running at: fkHz t OSC RAMP == 100 1 tR C RAMP T T =´ ´ = ´ - 051 1 10 5 . Solving for RT x CT yields 2 x 10-4. Selecting standard components values, CT = 270pF, and RT = 36.5kΩ. PWM SECTION Pulse Width Modulator The PWM section of the ML4805 is straightforward, but there are several points which should be noted. Foremost among these is its inherent synchronization to the PFC section of the device. The PWM is capable of current- mode or voltage mode operation. In current-mode applications, the PWM ramp (RAMP 2) is usually derived directly from a current sensing resistor or current transformer in the primary of the output stage, and is thereby representative of the current flowing in the converter’s output stage. DC ILIMIT, which provides cycle-by-cycle current limiting, is typically connected to RAMP 2 in such applications. For voltage-mode operation or certain specialized applications, RAMP 2 can be connected to a separate RC timing network to generate a voltage ramp against which VDC will be compared. Under these conditions, the use of voltage feedforward from the PFC buss can assist in line regulation accuracy and response. As in current mode operation, the DC ILIMIT input is used for output stage overcurrent protection. No voltage error amplifier is included in the PWM stage of the ML4805, as this function is generally performed on the output side of the PWM’s isolation boundary. To facilitate the design of optocoupler feedback circuitry, an offset has been built into the PWM’s RAMP 2 input which allows VDC to command a zero percent duty cycle for input voltages below 1.25V. PWM Current Limit The DC ILIMIT pin is a direct input to the cycle-by-cycle current limiter for the PWM section. Should the input voltage at this pin ever exceed 1.5V, the output of the PWM will be disabled until the output flip-flop is reset by the clock pulse at the start of the next PWM power cycle. VIN OK Comparator The VIN OK comparator monitors the DC output of the PFC and inhibits the PWM if this voltage on VFB is less than its nominal 2.5V. Once this voltage reaches 2.5V, which corresponds to the PFC output capacitor being charged to its rated boost voltage, the soft-start commences. PWM Control (RAMP 2) When the PWM section is used in current mode, RAMP 2 is generally used as the sampling point for a voltage representing the current in the primary of the PWM’s output transformer, derived either by a current sensing resistor or a current transformer. In voltage mode, it is the input for a ramp voltage generated by a second set of timing components (RRAMP2, CRAMP2), which will have a minimum value of zero volts and should have a peak value of approximately 5V. In voltage mode operation, feedforward from the PFC output buss is an excellent way to derive the timing ramp for the PWM stage. Soft Start Start-up of the PWM is controlled by the selection of the external capacitor at SS. A current source of 25µA supplies the charging current for the capacitor, and start- up of the PWM begins at 1.25V. Start-up delay can be programmed by the following equation: Ct A V SS DELAY =× 25 125 µ . (6) where CSS is the required soft start capacitance, and tDELAY is the desired start-up delay. It is important that the time constant of the PWM soft-start allow the PFC time to generate sufficient output power for the PWM section. The PWM start-up delay should be at least 5ms. Solving for the minimum value of CSS: Cms A V nF SS =× = 5 25 125 100 µ . In the ML4805, the operating frequency of the PFC section is fixed at 1/2 of the PWM's operating frequency. This is done through the use of a 2:1 digital frequency divider ("T" flip-flop) linking the two functional sections of the IC. FUNCTIONAL DESCRIPTION (Continued) |
Ähnliche Teilenummer - ML4805CS |
|
Ähnliche Beschreibung - ML4805CS |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |