ML4821IS datasheet(7/12 Pages) MICRO-LINEAR

Teilenummer	ML4821IS

Bauteilbeschribung	Power Factor Controller

Download	12 Pages

Scroll/Zoom	100%

Hersteller	MICRO-LINEAR [Micro Linear Corporation]

Direct Link	http://www.microlinear.com

Logo

7 / 12 page

7

ML4821

Micro Linear

6

7

9

–

+

S.S

INV

+8V

VREF

+8V

6.2k

Ω

EA OUT

The output of the gain modulator is a current which

appears on IA+ to form the reference for the current error

amplifier and is given as:

IK I

V

GM

SINE

EA

=×

×

−

(. )

08

where:

ISINE is the current in the dropping resistor, VEA

is the output of the error amplifier and K is a

constant determined by the VRMS input.

The output current of the gain modulator is limited to:

I

R

GM MAX

T

()

.

= 25

This sets the system current limit.The multiplier output

current is converted into the reference voltage for the

current (IA) amplifier through a resistor to ground on IA+.

Figure 6 shows the gain adjustor (K) with respect to the

voltage at VRMS. The curve has been separated in two

parts. The right hand part is for operation under normal

conditions in the voltage range from minimum line

voltage to maximum line voltage (90VAC to 260VAC).

85VAC on the curve has been chosen to account for

tolerances. Under normal operating conditions as input

voltage decreases the gain increases compensating for the

drop in the loop gain.

Under brownout conditions (below 85VAC) the gain

decreases to limit the amount of current that is drawn

from the line thus preventing an overload condition. This

is a very useful feature since in many cases the load for a

PFC is a constant power load. The input current has to go

high to compensate for a drop in the input voltage.

Figure 5. Output Saturation Voltage vs. Output Current.

Figure 6. K-factor. Gain Modulator gain with

respect to the voltage at VRMS.

0.5

0.4

0.3

0.2

0.1

0

135

7

46

0

85VAC

0.23

DESIGN

FOR

NORMAL

OPERATIONS

THIS IS THE MINIMUM

OPERATING

VOLTAGE POINT

THIS GAIN CURVE TAKES

OUT THE 1/(VIN)2

DEPENDENCY OF THE

VOLTAGE CONTROL LOOP

120VAC

OPERATING BOUNDRY

220VAC

K

2

VRMS

DESIGN

FOR

BROWNOUT

Figure 3. Error and Current Amplifier Configuration

Figure 4. Error Amplifier Open-loop Gain and Phase vs.

Frequency.

VCC = 15V

VO = 1.0V TO 5.0V

RL = 100kΩ

TA= 25°C

GAIN

PHASE

100

80

60

40

20

0

–20

10

100

1.0k

10k

100k

1.0M

10M

0

–30

60

90

120

150

180

f, FREQUENCY (Hz)

SOURCE SATURATION

(LOAD TO GROUND)

VCC

TA = 25°C

TA = –55°C

TA = 25°C

VCC = 15V

80

µs PULSED LOAD

120 Hz RATE

SINK SATURATION

(LOAD TO VCC)

GND

0

–1.0

–2.0

3.0

2.0

1.0

0

200

400

600

800

IO, OUTPUT LOAD CURRENT (mA)

Ähnliche Beschreibung - ML4821IS

Hersteller	Teilenummer	Datenblatt	Bauteilbeschribung
Unisonic Technologies	7524-D08-T	117Kb / 5P	POWER FACTOR CONTROLLER
ON Semiconductor	MC33232	213Kb / 15P	Power Factor Controller January, 2007 ??Rev. 2
New Japan Radio	NJM2375	335Kb / 9P	POWER FACTOR CONTROLLER
ON Semiconductor	NCP1650	230Kb / 31P	Power Factor Controller March, 2015 ??Rev. 13
Unisonic Technologies	UTCKA7524	66Kb / 4P	POWER FACTOR CONTROLLER
ON Semiconductor	NCP1650	233Kb / 31P	Power Factor Controller October, 2005 ??Rev. 10
Micro Linear Corporatio...	ML4812	215Kb / 16P	Power Factor Controller
List of Unclassifed Man...	SG3561A	1Mb / 19P	POWER FACTOR CONTROLLER
Linear Technology	LT1249	203Kb / 12P	Power Factor Controller
Fairchild Semiconductor	ML4812	348Kb / 16P	Power Factor Controller
E-Tech Electronics LTD	7524	123Kb / 5P	POWER FACTOR CONTROLLER

More results

ML4821IS Datenblatt(PDF) 7 Page - Micro Linear Corporation

ML4821IS Datenblatt(HTML) 7 Page - Micro Linear Corporation

Ähnliche Teilenummer - ML4821IS

Ähnliche Beschreibung - ML4821IS

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

Datenblatt Download

Link URL