Datenblatt-Suchmaschine für elektronische Bauteile |
|
6--23629--0 Datenblatt(PDF) 4 Page - Tyco Electronics |
|
6--23629--0 Datenblatt(HTML) 4 Page - Tyco Electronics |
4 / 5 page 408--4070 Pneumatic Head Assembly 679304--1 Rev D 4 of 5 Tyco Electronics Corporation A maintenance and inspection program should be performed periodically to ensure dependable and uniform terminations. The head assembly should be inspected once a month. Frequency of inspection should be adjusted to suit your requirements through experience. Frequency of inspection depends on: 1. The care, amount of use, and handling of the head. 2. The type and size of the product crimped. 3. The degree of operator skill. 4. The presence of abnormal amounts of dust and dirt. 5. Your own established standards. For die closure inspections and plug gage dimensions, refer to the instruction sheet supplied with the appropriate die assembly. 4.1. Cleaning Remove dust, moisture, and other contaminants with a clean, soft brush, or a soft, lint--free cloth. DO NOT use objects or cleaning materials that could damage the head assembly. Re--lubricate the head assembly as instructed in Paragraph 4.3 before placing it back into service. 4.2. Visual Inspection 1. Inspect the head assembly for missing pins and retaining rings. If parts are missing or defective, replace them by referring to Section 5. 2. Check all bearing surfaces for wear. Make sure the rollers turn freely with minimal resistance. Replace any worn parts. 3. Inspect the crimping areas of the die assembly for flattened, chipped, or broken areas. Although the dies may gage within permissible limits, worn or damaged die closure surfaces may affect the quality of the crimp. 4.3. Lubrication Lubricate all pins, pivot points, and bearing surfaces with a high quality grease. Use Dow Corning Molykote paste, which is a commercially available lubricant. Lubricate according to the following schedule: Head used in daily production — lubricate daily Head used daily (occasional) — lubricate weekly Head used weekly — lubricate monthly Wipe excess grease from the head assembly, particularly in the die closure areas. Grease transferred from the die closure area onto certain terminations may affect the electrical characteristics of a termination. 5. REPLACEMENT AND REPAIR Replacement parts and recommended spares are listed in Figure 4. The recommended spares should be stocked for immediate replacement. Order replacement parts through your Representative, or call 1--800--526--5142, or send a facsimile of your purchase order to 1--717--986--7605, or write to: CUSTOMER SERVICE (38--35) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105--3608 For customer repair service, call 1--800--526--5136. 6. REVISION SUMMARY Revisions to this instruction sheet include: S Added “Original Instructions” to page 1 Dow Corning and Molykote are registered trademarks of Dow Corning Corporation. NOTE i |
Ähnliche Teilenummer - 6--23629--0 |
|
Ähnliche Beschreibung - 6--23629--0 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |