Datenblatt-Suchmaschine für elektronische Bauteile |
|
0-59907-7 Datenblatt(PDF) 3 Page - Tyco Electronics |
|
0-59907-7 Datenblatt(HTML) 3 Page - Tyco Electronics |
3 / 3 page 408- 9809 Retrofit Kits 59907- [ ], 1901775- 1, 1901776- 1, and 1901777- 1 3 of 3 Rev C Tyco Electronics Corporation Figure 3 Coupler Guard Switch Cover The BROWN wire is a jumper between the RUN and RESET switches. If it is not long enough to be pulled through the two openings to allow easy soldering, substitute it with a length of 0.5mm2 [20 AWG] stranded wire,preferably with brown insulation. 7. Solder the switches: a. Obtain the GREEN switch and solder the WHITE conductor to one of the solder tabs and the BROWN jumper to the other solder tab. b. Obtain the RED switch and solder the BLUE conductor to one of the solder tabs and the ORANGE conductor to the other solder tab. c. Obtain the YELLOW switch and solder the BLACK conductor to one of the SQUARE solder tabs and to one of the ROUND solder tabs. Solder the BROWN jumper to the other SQUARE solder tab. Then solder the RED conductor to one of the ROUNDED solder tabs. Soldering the BLACK conductor to the two tabs can be best accomplished by stripping enough insulation from the wire to thread the conductor through the holes in the two tabs (thereby commoning them on the conductor) and then soldering them. 8. Check the wiring connections for correct placement and solder joints. 9. Reconnect the green wire (with the ring terminal crimped on it) to the tube handle using the 4--40 screw and washer. 10. Place the switch cover on a solid surface and obtain a piece of 3/8--in. tubing (or something of the same approximate size that will not press upon the switch itself but will provide an even distribution of pressure on the switch housing) and press--fit the switches into their respective openings. Take care to align the beveled portion of each switch housing with its identifying marking on the switch cover. Take care to ensure that there are no wires in contact with the housing. 11. Install the guard to the switch cover and secure it with the two slotted head screws provided with the retrofit kit. 12. Carefully slide the switch assembly back onto the handle tube and secure it with the two screws removed in Step 3 of Paragraph 3.1. 13. Apply pipe sealant to the threads of the handle tube and replace the quick--coupler. 14. Slide the grip sleeve up the handle tube until it is butted against the switch cover. 15. Carefully install the strain relief removed in Step 3 of Paragraph 3.1, Handle Control Disassembly by fitting it around the wire entering the handle tube and pushing it into the opening in the handle tube until it is seated. 4. REVISION SUMMARY Revisions to this instruction sheet include: S Added “Original Instructions” to page 1 NOTE i NOTE i CAUTION ! |
Ähnliche Teilenummer - 0-59907-7 |
|
Ähnliche Beschreibung - 0-59907-7 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |