Datenblatt-Suchmaschine für elektronische Bauteile |
|
LTM8005 Datenblatt(PDF) 8 Page - Linear Technology |
|
LTM8005 Datenblatt(HTML) 8 Page - Linear Technology |
8 / 26 page LTM8005 8 8005f For more information www.linear.com/LTM8005 resistor. OPENLED status is updated only during PWM high state and latched during PWM low state. If not used, leave floating or tie to GND. ISMON (Pin J1): LED Current Report Pin. The LED cur- rent is reported as VISMON = (LED current)/1.6. Leave the ISMON pin unconnected if not used. When PWM is low, ISMON is driven to ground. Bypass with a 47nF capacitor or higher if needed. Do not drive this pin with an external source. AUX (Pin J2): Auxiliary Pin. This pin is internally con- nected to VOUT to ease layout. Conveniently located next to FB, it is provided to simplify layout of the output voltage feedback network. VREF (Pin J6): Voltage Reference Output Pin. Typically 2.015V. This pin drives a resistor divider for the CTRL pins, either for analog dimming or for temperature limit/ compensation of the LED load. It can supply up to 100µA. Do not drive this pin with an external source. PWM (Pin J7): PWM Input Signal Pin. A low signal turns off switching, idles the oscillator, disconnects the VC pin from all internal loads, and disconnects the output load from VOUT. PWM has an internal 500k pull-down resis- tor. If not used, connect to VREF. RAMP (Pin J8): The RAMP pin is used for spread spec- trum frequency modulation. The internal switching fre- quency is spread out to 70% of the original value, where the modulation frequency is set by 12µA/(2 • 1V • CRAMP). If not used, tie this pin to GND. FB (Pin K2): Voltage Loop Feedback Pin. FB is intended for constant-voltage regulation or for LED protection/open LED detection. The internal transconductance amplifier with output VC regulates FB to 1.25V (nominal) through the DC/DC converter. If the FB input is regulating the loop, and LED current is less than 0.15A (typical), the OPENLED pull-down is asserted. This action may signal an open LED fault. If FB is driven above 1.3V (by an external power sup- ply spike, for example), the internal N-Channel MOSFET is turned off and the load is disconnected from VOUT to protect the LEDs from an overcurrent event. Do not tie this pin to GND as the SHORTLED will be asserted and the part will be shut down. VC (Pin K3): Transconductance Error Amplifier Output Pin. Used to stabilize the control loop with an RC network. This pin is high impedance when PWM is low, a feature that stores the demanded current state variable for the next PWM high transition. Connect a capacitor between this pin and GND; a resistor in series with the capacitor is recom- mended for fast transient response. Do not leave this pin open, and do not drive this pin with an external source. SS (Pin K4): Soft-Start Pin. This pin modulates oscillator frequency and compensation pin voltage (VC). The soft- start interval is set with an external capacitor. The pin has a 28µA (typical) pull-up current source to an internal 2.5V rail. This pin can be used as fault timer. Provided the SS pin has exceeded 1.7V to complete a blanking period at start-up, the pull-up current source is disabled and a 2.8µA pull-down current is enabled when any one of the following fault conditions happen: 1. LED overcurrent (ILED > 2.4A) 2. Output short (FB < 0.3V after start-up) 3. Thermal limit The SS pin must be discharged below 0.2V to re-initiate a soft-start cycle. Switching is disabled until SS begins to recharge. It is important to select a capacitor large enough that FB can exceed 0.3V under normal load conditions before SS exceeds 1.7V. Do not leave this pin open and do not drive this pin with an external source. RT (Pin K5): Switching Frequency Adjustment Pin. Set the frequency using a resistor to GND. Do not leave the RT pin open. Do not drive this pin with an external source. CTRL1, CTRL2 (Pin K6, K7): Current Sense Threshold Adjustment. CTRL1 and CTRL2 have identical functions. The output current is regulated by CTRL1 or CTRL2. The pin with the lowest voltage takes precedence. For 0.1V < VCTRLx < 1V the LED current is VCTRLx • 1.5A less an offset. For VCTRLx > 1.2V the current sense threshold is constant at the full-scale value of 1.6A. For 1V < VCTRLx < 1.2V, the dependence of the current sense threshold upon VCTRLx transitions from a linear function to a constant value, reaching 98% of full-scale value by VCTRLx = 1.1V. Do not leave this pin open. If not used, tie to VREF. Connect either CTRL pin to GND for zero LED current. PIN FUNCTIONS |
Ähnliche Teilenummer - LTM8005 |
|
Ähnliche Beschreibung - LTM8005 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |