Datenblatt-Suchmaschine für elektronische Bauteile |
|
X1227V8Z Datenblatt(PDF) 4 Page - Intersil Corporation |
|
X1227V8Z Datenblatt(HTML) 4 Page - Intersil Corporation |
4 / 28 page 4 FN8099.1 September 15, 2005 ABSOLUTE MAXIMUM RATINGS Temperature Under Bias ................... -65°C to +135°C Storage Temperature ........................ -65°C to +150°C Voltage on VCC, VBACK pin (respect to ground)...............................-0.5V to 7.0V Voltage on SCL, SDA, X1 and X2 pin (respect to ground) ............... -0.5V to 7.0V or 0.5V above VCC or VBACK (whichever is higher) DC Output Current .............................................. 5 mA Lead Temperature (Soldering, 10 sec) .............. 300°C Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and the functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute max- imum rating conditions for extended periods may affect device reliability. DC OPERATING CHARACTERISTICS (Temperature = -40°C to +85°C, unless otherwise stated.) OPERATING CHARACTERISTICS Notes: (1) The device enters the Active state after any start, and remains active: for 9 clock cycles if the Device Select Bits in the Slave Address Byte are incorrect or until 200nS after a stop ending a read or write operation. (2) The device enters the Program state 200nS after a stop ending a write operation and continues for tWC. (3) The device goes into the Timekeeping state 200nS after any stop, except those that initiate a nonvolatile write cycle; tWC after a stop that initiates a nonvolatile write cycle; or 9 clock cycles after any start that is not followed by the correct Device Select Bits in the Slave Address Byte. (4) For reference only and not tested. (5) VIL = VCC x 0.1, VIH = VCC x 0.9, fSCL = 400KHz (6) VCC = 0V (7) VBACK = 0V (8) VSDA = VSCL=VCC, Others = GND or VCC Symbol Parameter Conditions Min Typ Max Unit Notes VCC Main Power Supply 2.7 5.5 V VBACK Backup Power Supply 1.8 5.5 V VCB Switch to Backup Supply VBACK -0.2 VBACK -0.1 V VBC Switch to Main Supply VBACK VBACK +0.2 V Symbol Parameter Conditions Min Typ Max Unit Notes ICC1 Read Active Supply Current VCC = 2.7V 400 µA 1, 5, 7, 14 VCC = 5.0V 800 µA ICC2 Program Supply Current (nonvolatile) VCC = 2.7V 2.5 mA 2, 5, 7, 14 VCC = 5.0V 3.0 mA ICC3 Main Timekeeping Current VCC = 2.7V 10 µA 3, 7, 8, 14, 15 VCC = 5.0V 20 µA IBACK Timekeeping Current – (Low Voltage Sense and Watchdog Timer disabled VBACK = 1.8V 1.25 µA 3, 6, 9, 14, 15 “See Perfor- mance Data” VBACK = 3.3V 1.5 µA ILI Input Leakage Current 10 µA 10 ILO Output Leakage Current 10 µA 10 VIL Input LOW Voltage -0.5 VCC x 0.2 or VBACK x 0.2 V13 VIH Input HIGH Voltage VCC x 0.7 or VBACK x 0.7 VCC + 0.5 or VBACK + 0.5 V13 VHYS Schmitt Trigger Input Hysteresis VCC related level .05 x VCC or .05 x VBACK V13 VOL1 Output LOW Voltage for SDA and RESET VCC = 2.7V 0.4 V 11 VCC = 5.5V 0.4 X1227 |
Ähnliche Teilenummer - X1227V8Z |
|
Ähnliche Beschreibung - X1227V8Z |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |