Datenblatt-Suchmaschine für elektronische Bauteile
  German  ▼
ALLDATASHEETDE.COM

X  

MC33023DW Datenblatt(PDF) 8 Page - ON Semiconductor

Teilenummer MC33023DW
Bauteilbeschribung  High Speed Single-Ended PWM Controller
Download  19 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Hersteller  ONSEMI [ON Semiconductor]
Direct Link  http://www.onsemi.com
Logo ONSEMI - ON Semiconductor

MC33023DW Datenblatt(HTML) 8 Page - ON Semiconductor

Back Button MC33023DW Datasheet HTML 4Page - ON Semiconductor MC33023DW Datasheet HTML 5Page - ON Semiconductor MC33023DW Datasheet HTML 6Page - ON Semiconductor MC33023DW Datasheet HTML 7Page - ON Semiconductor MC33023DW Datasheet HTML 8Page - ON Semiconductor MC33023DW Datasheet HTML 9Page - ON Semiconductor MC33023DW Datasheet HTML 10Page - ON Semiconductor MC33023DW Datasheet HTML 11Page - ON Semiconductor MC33023DW Datasheet HTML 12Page - ON Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 8 / 19 page
background image
MC34023 MC33023
8
MOTOROLA ANALOG IC DEVICE DATA
OPERATING DESCRIPTION
The MC33023 and MC34023 series are high speed, fixed
frequency, single–ended pulse width modulator controllers
optimized for high frequency operation. They are specifically
designed for Off–Line and DC–to–DC converter applications
offering the designer a cost effective solution with minimal
external components. A representative block diagram is
shown in Figure 18.
Oscillator
The oscillator frequency is programmed by the values
selected for the timing components RT and CT. The RT pin is
set to a temperature compensated 3.0 V. By selecting the
value of RT, the charge current is set through a current mirror
for the timing capacitor CT. This charge current runs
continuously through CT. The discharge current is ratioed to
be 10 times the charge current, which yields the maximum
duty cycle of 90%. CT is charged to 2.8 V and discharged to
1.0 V. During the discharge of CT, the oscillator generates an
internal blanking pulse that resets the PWM Latch and,
inhibits the outputs. The threshold voltage on the oscillator
comparator is trimmed to guarantee an oscillator accuracy of
5.0% at 25
°C.
Additional dead time can be added by externally
increasing the charge current to CT as shown in Figure 23.
This changes the charge to discharge ratio of CT which is set
internally to Icharge/10 Icharge. The new charge to discharge
ratio will be:
% Deadtime
+
Iadditional ) Icharge
10 (Icharge)
A bidirectional clock pin is provided for synchronization or
for master/slave operation. As a master, the clock pin
provides a positive output pulse during the discharge of CT.
As a slave, the clock pin is an input that resets the PWM latch
and blanks the drive output, but does not discharge CT.
Therefore, the oscillator is not synchronized by driving the
clock pin alone. Figures 27, 28 and 29 provide suggested
synchronization.
Error Amplifier
A fully compensated Error Amplifier is provided. It features
a typical DC voltage gain of 95 dB and a gain bandwidth
product of 8.3 MHz with 75 degrees of phase margin
(Figure 3). Typical application circuits will have the
noninverting input tied to the reference. The inverting input
will typically be connected to a feedback voltage generated
from the output of the switching power supply. Both inputs
have a common mode voltage (VCM) input range of 1.5 V to
5.5 V. The Error Amplifier Output is provided for external loop
compensation.
Soft–Start Latch
Soft–Start is accomplished in conjunction with an external
capacitor. The Soft–Start capacitor is charged by an internal
9.0
µA current source. This capacitor clamps the output of
the error amplifier to less than its normal output voltage, thus
limiting the duty cycle. The time it takes for a capacitor to
reach full charge is given by:
t
[ (4.5 • 105)CSoft-Start
A Soft–Start latch is incorporated to prevent erratic
operation of this circuitry. Two conditions can cause the
Soft–Start circuit to latch so that the Soft–Start capacitor
stays discharged. The first condition is activation of an
undervoltage lockout of either VCC or Vref. The second
condition is when current sense input exceeds 1.4 V. Since
this latch is “set dominant”, it cannot be reset until either of
these signals is removed and, the voltage at CSoft–Start is less
than 0.5 V.
PWM Comparator and Latch
A PWM circuit typically compares an error voltage with a
ramp signal. The outcome of this comparison determines the
state of the output. In voltage mode operation the ramp signal
is the voltage ramp of the timing capacitor. In current mode
operation the ramp signal is the voltage ramp induced in a
current sensing element. The ramp input of the PWM
comparator is pinned out so that the user can decide which
mode of operation best suits the application requirements.
The ramp input has a 1.25 V offset such that whenever the
voltage at this pin exceeds the error amplifier output voltage
minus 1.25 V, the PWM comparator will cause the PWM latch
to set, disabling the outputs. Once the PWM latch is set, only
a blanking pulse by the oscillator can reset it, thus initiating
the next cycle.
Current Limiting and Shutdown
A pin is provided to perform current limiting and shutdown
operations. Two comparators are connected to the input of
this pin. The reference voltage for the current limit
comparator is not set internally. A pin is provided so the user
can set the voltage. When the voltage at the current limit
input pin exceeds the externally set voltage, the PWM latch is
set, disabling the output. In this way cycle–by–cycle current
limiting is accomplished. If a current limit resistor is used in
series with the power devices, the value of the resistor is
found by:
RSense +
ILimit Reference Voltage
Ipk (switch)
If the voltage at this pin exceeds 1.4 V, the second
comparator is activated. This comparator sets a latch which,
in turn, causes the soft start capacitor to be discharged. In
this way a “hiccup” mode of recovery is possible in the case
of output short circuits. If a current limit resistor is used in
series with the output devices, the peak current at which the
controller will enter a “hiccup” mode is given by:
Ishutdown +
1.4 V
RSense


Ähnliche Teilenummer - MC33023DW

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
ON Semiconductor
MC33023DW ONSEMI-MC33023DW Datasheet
441Kb / 18P
   High Speed Single?묮nded PWM Controller
October, 2005 ??Rev. 6
MC33023DWG ONSEMI-MC33023DWG Datasheet
441Kb / 18P
   High Speed Single?묮nded PWM Controller
October, 2005 ??Rev. 6
MC33023DWR2 ONSEMI-MC33023DWR2 Datasheet
441Kb / 18P
   High Speed Single?묮nded PWM Controller
October, 2005 ??Rev. 6
MC33023DWR2G ONSEMI-MC33023DWR2G Datasheet
441Kb / 18P
   High Speed Single?묮nded PWM Controller
October, 2005 ??Rev. 6
More results

Ähnliche Beschreibung - MC33023DW

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
ON Semiconductor
MC34025 ONSEMI-MC34025 Datasheet
516Kb / 20P
   High Speed Double-Ended PWM Controller
1996 REV 1
MC33025 ONSEMI-MC33025_12 Datasheet
499Kb / 20P
   High Speed Double-Ended PWM Controller
October, 2012 ??Rev. 9
MC34025 ONSEMI-MC34025_12 Datasheet
499Kb / 20P
   High Speed Double-Ended PWM Controller
October, 2012 ??Rev. 9
MC34023 ONSEMI-MC34023_05 Datasheet
441Kb / 18P
   High Speed Single?묮nded PWM Controller
October, 2005 ??Rev. 6
logo
Texas Instruments
UC1823AJ883B TI-UC1823AJ883B Datasheet
456Kb / 9P
[Old version datasheet]   High Speed PWM Controller
UC3823N TI-UC3823N Datasheet
2Mb / 13P
[Old version datasheet]   HIGH SPEED PWM CONTROLLER
UC3824DW TI1-UC3824DW Datasheet
704Kb / 14P
[Old version datasheet]   HIGH SPEED PWM CONTROLLER
UCC3829-1 TI1-UCC3829-1 Datasheet
196Kb / 11P
[Old version datasheet]   High Speed PWM Controller
UC1823 TI-UC1823 Datasheet
409Kb / 7P
[Old version datasheet]   High Speed PWM Controller
UC1823A TI-UC1823A Datasheet
303Kb / 15P
[Old version datasheet]   High Speed PWM Controller
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19


Datenblatt Download

Go To PDF Page


Link URL




Privatsphäre und Datenschutz
ALLDATASHEETDE.COM
War ALLDATASHEET hilfreich?  [ DONATE ] 

Über Alldatasheet   |   Werbung   |   Kontakt   |   Privatsphäre und Datenschutz   |   Linktausch   |   Hersteller
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com