ST7DALI datasheet(49/141 Pages) STMICROELECTRONICS

Teilenummer	ST7DALI

Bauteilbeschribung	8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI, DALI

Download	141 Pages

Scroll/Zoom	100%

Hersteller	STMICROELECTRONICS [STMicroelectronics]

Direct Link	http://www.st.com

Logo

49 / 141 page

ST7DALI

49/141

I/O PORTS (Cont’d)

Analog alternate function

Configure the I/O as floating input to use an ADC

input. The analog multiplexer (controlled by the

ADC registers) switches the analog voltage

present on the selected pin to the common analog

rail, connected to the ADC input.

Analog Recommendations

Do not change the voltage level or loading on any

I/O while conversion is in progress. Do not have

clocking pins located close to a selected analog

pin.

WARNING: The analog input voltage level must

be within the limits stated in the absolute maxi-

mum ratings.

10.3 I/O PORT IMPLEMENTATION

The hardware implementation on each I/O port de-

pends on the settings in the DDR and OR registers

and specific I/O port features such as ADC input or

open drain.

Switching these I/O ports from one state to anoth-

er should be done in a sequence that prevents un-

wanted side effects. Recommended safe transi-

tions are illustrated in Figure 31. Other transitions

are potentially risky and should be avoided, since

they may present unwanted side-effects such as

spurious interrupt generation.

Figure 31. Interrupt I/O Port State Transitions

10.4 UNUSED I/O PINS

Unused I/O pins must be connected to fixed volt-

age levels. Refer to Section 13.8.

10.5 LOW POWER MODES

10.6 INTERRUPTS

The external interrupt event generates an interrupt

if the corresponding configuration is selected with

DDR and OR registers and if the I bit in the CC

register is cleared (RIM instruction).

Mode

Description

WAIT

No effect on I/O ports. External interrupts

cause the device to exit from WAIT mode.

HALT

No effect on I/O ports. External interrupts

cause the device to exit from HALT mode.

Interrupt Event

Event

Flag

Enable

Control

Bit

Exit

from

Wait

Exit

from

Halt

External interrupt on

selected external

event

-

DDRx

ORx

Yes

01

floating/pull-up

interrupt

INPUT

00

floating

(reset state)

INPUT

10

open-drain

OUTPUT

11

push-pull

OUTPUT

XX

= DDR, OR

1

Ähnliche Beschreibung - ST7DALI

Hersteller	Teilenummer	Datenblatt	Bauteilbeschribung
STMicroelectronics	ST7LITE2	1Mb / 131P	8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI August 2003 Rev. 2.0
	ST7LITE0	1Mb / 122P	8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI August 2003 Rev. 2.4
	ST7FLIT19BF1B6	2Mb / 159P	8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 5 TIMERS, SPI
	ST7LITE1XB	2Mb / 157P	8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 5 TIMERS, SPI
	ST7LITE1XB	2Mb / 159P	8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 5 TIMERS, SPI
	ST7LITE1	1Mb / 131P	8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 4 TIMERS, SPI December 2004 Rev. 2.0
	ST7FLIT15BF1M6	2Mb / 159P	8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 5 TIMERS, SPI
	ST7L05	1Mb / 104P	8-bit MCU for automotive with single voltage Flash memory, data EEPROM, ADC, timers, SPI
	ST7LITE3	3Mb / 167P	8-BIT MCU WITH SINGLE VOLTAGE FLASH, DATA EEPROM, ADC, TIMERS, SPI, LINSCI
	ST7LITE3XF2	2Mb / 173P	8-bit MCU with single voltage Flash, data EEPROM, ADC, timers, SPI, LINSCI?

More results

ST7DALI Datenblatt(PDF) 49 Page - STMicroelectronics

ST7DALI Datenblatt(HTML) 49 Page - STMicroelectronics

Ähnliche Teilenummer - ST7DALI

Ähnliche Beschreibung - ST7DALI

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datenblatt Download

Link URL