 |
Datenblatt-Suchmaschine für elektronische Bauteile |
|
|
Datenblatt-Suchmaschine für elektronische Bauteile |
|
MCH02 Datenblatt(PDF) 4 Page - Rohm |
|
||||||||||||||||||||||||||||||
MCH02 Datenblatt(HTML) 4 Page - Rohm |
|
|
4 / 7 page  MCH02 Ceramic capacitors 4/6 Items Performance Resistance to solderin heat Test Method (As per JIS C 5101-1, JIS C 5101-10) As per 4.14 of JIS C 5101-1. As per 4.10 of JIS C 5101-10 The solder specified in JIS Z 3282. H63A shall be used. The specimens shall be immersed into the solder at 260 +/−5°C for 5+/−0.5s so that both end terminations are completely under the solder. Pre-heating at 150 +/−10°C for 1 to 2min Initial measurements prior to test shall be performed after the thermal Pre-conditioning specified in Remarks (1). Final measurements shall be made after the specimens have been left at room temperature as per Table3. As per 4.13 of JIS C 5101-1. As per 4.8 ofJIS C 5101-10 A 1N weight for 10 +/−1s shall be applied to the soldered specimens as shown by the arrow mark in the below sketch. As per 4.35 of JIS C 5101-1. As per 4.9 of JIS C 5101-10 Glass epoxy board with soldered specimens shall be bent till 1mm by 1.0mm/s. No. 8 End termination adherence 9 Bending strength 10 Within +/−0.25pF Within +/−0.5pF Within +/−0.25pF Appearance Dielectric loss tangent Within specified initial value. Insulation resistance Within specified initial value. Withstanding voltage No defects shall be allowed. Without peeling or sign of peeling shall be allowed on the end terminations. Change rate from initial value Change rate from initial value Without mechanical damage. Table3 24 +/−2 h Time Table3 24 +/−2 h Time Applied pressure Capacitor Substrate Appearance Without mechanical damage. Vibration As per 4.17 of JIS C 5101-1. The specimens shall be soldered on the specified test jig. Final measurements shall be made after the specimens have been left at room temperature as per Table3. [Condition] Directions : 2h each X, Y and Z directions Total : 6h Frequency range : 10 to 55 to 10Hz(1min) Applitude : 1.5mm (shall not exceed acceleration196m/s2) 11 Appearance Dielectric loss tangent Within specified initial value. Change rate from initial value Without mechanical damage. |
Ähnliche Teilenummer - MCH02 |
|
Ähnliche Beschreibung - MCH02 |
|
|
|
Link URL |
| Privatsphäre und Datenschutz |
| ALLDATASHEETDE.COM |
| War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
German ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
