Datenblatt-Suchmaschine für elektronische Bauteile |
|
SN74CBT16811CDLRG4 Datenblatt(PDF) 2 Page - Texas Instruments |
|
SN74CBT16811CDLRG4 Datenblatt(HTML) 2 Page - Texas Instruments |
2 / 11 page SN74CBT16811C 24BIT FET BUS SWITCH WITH PRECHARGED OUTPUTS 5V BUS SWITCH WITH 2V UNDERSHOOT PROTECTION SCDS118C − JANUARY 2003 − REVISED OCTOBER 2003 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 description/ordering information (continued) The SN74CBT16811C is organized as two 12-bit bus switches with separate output-enable (1OE, 2OE) inputs. It can be used as two 12-bit bus switches or as one 24-bit bus switch. When OE is low, the associated 12-bit bus switch is ON, and the A port is connected to the B port, allowing bidirectional data flow between ports. When OE is high, the associated 12-bit bus switch is OFF, and a high-impedance state exists between the A and B ports. The B port is precharged to BIASV through the equivalent of a 10-k Ω resistor when OE is high, or if the device is powered down (VCC = 0 V). During insertion (or removal) of a card into (or from) an active bus, the card’s output voltage may be close to GND. When the connector pins make contact, the card’s parasitic capacitance tries to force the bus signal to GND, creating a possible glitch on the active bus. This glitching effect can be reduced by using a bus switch with precharged bias voltage (BIASV) of the bus switch equal to the input threshold voltage level of the receivers on the active bus. This method will ensure that any glitch produced by insertion (or removal) of the card will not cross the input threshold region of the receivers on the active bus, minimizing the effects of live-insertion noise. This device is fully specified for partial-power-down applications using Ioff. The Ioff feature ensures that damaging current will not backflow through the device when it is powered down. The device has isolation during power off. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. ORDERING INFORMATION TA PACKAGE† ORDERABLE PART NUMBER TOP-SIDE MARKING SSOP − DL Tube SN74CBT16811CDL CBT16811C SSOP − DL Tape and reel SN74CBT16811CDLR CBT16811C −40 °C to 85°C TSSOP − DGG Tube SN74CBT16811CDGG CBT16811C −40 C to 85 C TSSOP − DGG Tape and reel SN74CBT16811CDGGR CBT16811C TVSOP − DGV Tape and reel SN74CBT16811CDGVR CY811C † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. FUNCTION TABLE (each 12-bit bus switch) INPUT INPUT/OUTPUT FUNCTION INPUT OE INPUT/OUTPUT A FUNCTION L B A port = B port H Z Disconnect B port = BIASV |
Ähnliche Teilenummer - SN74CBT16811CDLRG4 |
|
Ähnliche Beschreibung - SN74CBT16811CDLRG4 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |