Datenblatt-Suchmaschine für elektronische Bauteile |
|
74ALVTH16245DLG4 Datenblatt(PDF) 6 Page - Texas Instruments |
|
74ALVTH16245DLG4 Datenblatt(HTML) 6 Page - Texas Instruments |
6 / 24 page SN54ALVTH16245, SN74ALVTH16245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES066G – JUNE 1996 – REVISED APRIL 2002 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 electrical characteristics over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V (unless otherwise noted) PARAMETER TEST CONDITIONS SN54ALVTH16245 SN74ALVTH16245 UNIT PARAMETER TEST CONDITIONS MIN TYP† MAX MIN TYP† MAX UNIT VIK VCC = 3 V, II = –18 mA –1.2 –1.2 V VCC = 3 V to 3.6 V, IOH = –100 µA VCC–0.2 VCC–0.2 VOH VCC =3V IOH = –24 mA 2 V VCC = 3 V IOH = –32 mA 2 VCC = 3 V to 3.6 V, IOL = 100 µA 0.2 0.2 IOL = 16 mA 0.4 VOL IOL = 24 mA 0.5 V VOL VCC = 3 V IOL = 32 mA 0.5 V IOL = 48 mA 0.55 IOL = 64 mA 0.55 Control inputs VCC = 3.6 V, VI = VCC or GND ±1 ±1 Control inputs VCC = 0 or 3.6 V, VI = 5.5 V 10 10 II VI = 5.5 V 20 20 µA A or B ports VCC = 3.6 V VI = VCC 1 1 VI = 0 –5 –5 Ioff VCC = 0, VI or VO = 0 to 4.5 V ±100 µA IBHL‡ VCC = 3 V, VI = 0.8 V 75 75 µA IBHH§ VCC = 3 V, VI = 2 V –75 –75 µA IBHLO¶ VCC = 3.6 V, VI = 0 to VCC 500 500 µA IBHHO# VCC = 3.6 V, VI = 0 to VCC –500 –500 µA IEX|| VCC = 3 V, VO = 5.5 V 125 125 µA IOZ(PU/PD)k VCC ≤ 1.2 V, VO = 0.5 V to VCC, VI = GND or VCC, OE = don’t care ±100 ±100 µA VCC = 3.6 V, Outputs high 0.07 0.1 0.07 0.1 ICC VCC = 3.6 V, IO = 0, Outputs low 3.2 5 3.2 5 mA VI = VCC or GND Outputs disabled 0.07 0.1 0.07 0.1 ∆ICCh VCC = 3 V to 3.6 V, One input at VCC – 0.6 V, Other inputs at VCC or GND 0.2 0.2 mA Ci VCC = 3.3 V, VI = 3.3 V or 0 3.5 3.5 pF Cio VCC = 3.3 V, VO = 3.3 V or 0 8 8 pF † All typical values are at VCC = 3.3 V, TA = 25°C. ‡ The bus-hold circuit can sink at least the minimum low sustaining current at VIL max. IBHL should be measured after lowering VIN to GND and then raising it to VIL max. § The bus-hold circuit can source at least the minimum high sustaining current at VIH min. IBHH should be measured after raising VIN to VCC and then lowering it to VIH min. ¶ An external driver must source at least IBHLO to switch this node from low to high. # An external driver must sink at least IBHHO to switch this node from high to low. || Current into an output in the high state when VO > VCC k High-impedance state during power up or power down h This is the increase in supply current for each input that is at the specified TTL voltage level rather than V CC or GND. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. |
Ähnliche Teilenummer - 74ALVTH16245DLG4 |
|
Ähnliche Beschreibung - 74ALVTH16245DLG4 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |