Datenblatt-Suchmaschine für elektronische Bauteile
  German  ▼
ALLDATASHEETDE.COM

X  

ATTINY2313-20PU Datenblatt(PDF) 20 Page - ATMEL Corporation

Teilenummer ATTINY2313-20PU
Bauteilbeschribung  8-bit Microcontroller with 2K Bytes In-System Programmable Flash
Download  231 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Hersteller  ATMEL [ATMEL Corporation]
Direct Link  http://www.atmel.com
Logo ATMEL - ATMEL Corporation

ATTINY2313-20PU Datenblatt(HTML) 20 Page - ATMEL Corporation

Back Button ATTINY2313-20PU Datasheet HTML 16Page - ATMEL Corporation ATTINY2313-20PU Datasheet HTML 17Page - ATMEL Corporation ATTINY2313-20PU Datasheet HTML 18Page - ATMEL Corporation ATTINY2313-20PU Datasheet HTML 19Page - ATMEL Corporation ATTINY2313-20PU Datasheet HTML 20Page - ATMEL Corporation ATTINY2313-20PU Datasheet HTML 21Page - ATMEL Corporation ATTINY2313-20PU Datasheet HTML 22Page - ATMEL Corporation ATTINY2313-20PU Datasheet HTML 23Page - ATMEL Corporation ATTINY2313-20PU Datasheet HTML 24Page - ATMEL Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 20 / 231 page
background image
20
ATtiny2313/V
2543I–AVR–04/06
• Bit 2 – EEMPE: EEPROM Master Program Enable
The EEMPE bit determines whether writing EEPE to one will have effect or not.
When EEMPE is set, setting EEPE within four clock cycles will program the EEPROM at
the selected address. If EEMPE is zero, setting EEPE will have no effect. When EEMPE
has been written to one by software, hardware clears the bit to zero after four clock
cycles.
• Bit 1 – EEPE: EEPROM Program Enable
The EEPROM Program Enable Signal EEPE is the programming enable signal to the
EEPROM. When EEPE is written, the EEPROM will be programmed according to the
EEPMn bits setting. The EEMPE bit must be written to one before a logical one is writ-
ten to EEPE, otherwise no EEPROM write takes place. When the write access time has
elapsed, the EEPE bit is cleared by hardware. When EEPE has been set, the CPU is
halted for two cycles before the next instruction is executed.
• Bit 0 – EERE: EEPROM Read Enable
The EEPROM Read Enable Signal – EERE – is the read strobe to the EEPROM. When
the correct address is set up in the EEAR Register, the EERE bit must be written to one
to trigger the EEPROM read. The EEPROM read access takes one instruction, and the
requested data is available immediately. When the EEPROM is read, the CPU is halted
for four cycles before the next instruction is executed. The user should poll the EEPE bit
before starting the read operation. If a write operation is in progress, it is neither possible
to read the EEPROM, nor to change the EEAR Register.
Atomic Byte Programming
Using Atomic Byte Programming is the simplest mode. When writing a byte to the
EEPROM, the user must write the address into the EEAR Register and data into EEDR
Register. If the EEPMn bits are zero, writing EEPE (within four cycles after EEMPE is
written) will trigger the erase/write operation. Both the erase and write cycle are done in
one operation and the total programming time is given in Table 1. The EEPE bit remains
set until the erase and write operations are completed. While the device is busy with
programming, it is not possible to do any other EEPROM operations.
Split Byte Programming
It is possible to split the erase and write cycle in two different operations. This may be
useful if the system requires short access time for some limited period of time (typically
if the power supply voltage falls). In order to take advantage of this method, it is required
that the locations to be written have been erased before the write operation. But since
the erase and write operations are split, it is possible to do the erase operations when
the system allows doing time-consuming operations (typically after Power-up).
Erase
To erase a byte, the address must be written to EEAR. If the EEPMn bits are 0b01, writ-
ing the EEPE (within four cycles after EEMPE is written) will trigger the erase operation
only (programming time is given in Table 1). The EEPE bit remains set until the erase
operation completes. While the device is busy programming, it is not possible to do any
other EEPROM operations.
Write
To write a location, the user must write the address into EEAR and the data into EEDR.
If the EEPMn bits are 0b10, writing the EEPE (within four cycles after EEMPE is written)
will trigger the write operation only (programming time is given in Table 1). The EEPE bit
remains set until the write operation completes. If the location to be written has not been
erased before write, the data that is stored must be considered as lost. While the device
is busy with programming, it is not possible to do any other EEPROM operations.


Ähnliche Teilenummer - ATTINY2313-20PU

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
ATMEL Corporation
ATTINY2313-20PU ATMEL-ATTINY2313-20PU Datasheet
181Kb / 17P
   8-bit Microcontroller with 2K Bytes In-System Programmable Flash
More results

Ähnliche Beschreibung - ATTINY2313-20PU

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
ATMEL Corporation
ATTINY2313-20 ATMEL-ATTINY2313-20 Datasheet
1Mb / 223P
   8-bit Microcontroller with 2K Bytes In-System Programmable Flash
ATTINY2313 ATMEL-ATTINY2313_06 Datasheet
181Kb / 17P
   8-bit Microcontroller with 2K Bytes In-System Programmable Flash
AT90S2313 ATMEL-AT90S2313 Datasheet
387Kb / 8P
   8-Bit Microcontroller with 2K bytes In-System Programmable Flash
ATTINY20 ATMEL-ATTINY20 Datasheet
638Kb / 18P
   8-bit Microcontroller with 2K Bytes In-System Programmable Flash
ATTINY20 ATMEL-ATTINY20_11 Datasheet
5Mb / 224P
   8-bit Microcontroller with 2K Bytes In-System Programmable Flash
ATTINY2313 ATMEL-ATTINY2313 Datasheet
2Mb / 211P
   8-bit AVR Microcontroller with 2K Bytes In-System Programmable Flash
AT90S2313 ATMEL-AT90S2313 Datasheet
2Mb / 8P
   8-bit Microcontroller with 2K Bytes of In-System Programmable Flash
ATTINY22L ATMEL-ATTINY22L_1 Datasheet
884Kb / 56P
   8-bit Microcontroller with 2K Bytes of In-System Programmable Flash
ATTINY24A ATMEL-ATTINY24A Datasheet
545Kb / 20P
   8-bit Microcontroller with 2K/4K Bytes In-System Programmable Flash
ATTINY22L ATMEL-ATTINY22L Datasheet
252Kb / 11P
   8-bit Microcontroller with 2K Bytes of In-System Programmable Flash
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


Datenblatt Download

Go To PDF Page


Link URL




Privatsphäre und Datenschutz
ALLDATASHEETDE.COM
War ALLDATASHEET hilfreich?  [ DONATE ] 

Über Alldatasheet   |   Werbung   |   Kontakt   |   Privatsphäre und Datenschutz   |   Linktausch   |   Hersteller
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com