Datenblatt-Suchmaschine für elektronische Bauteile |
|
TDA8002CG Datenblatt(PDF) 10 Page - NXP Semiconductors |
|
TDA8002CG Datenblatt(HTML) 10 Page - NXP Semiconductors |
10 / 28 page 1999 Oct 12 10 Philips Semiconductors Product specification IC card interface TDA8002C Table 1 Clock circuitry definition Notes 1. X = don’t care. 2. In low-power mode. 3. fint = 32 kHz in low-power mode. MODE CLKSEL CLKDIV1 CLKDIV2 FREQUENCY OF CLK FREQUENCY OF CLKOUT HIGH LOW HIGH LOW 1 ⁄2fint 1 ⁄2fint HIGH LOW LOW LOW 1 ⁄4fxtal fxtal HIGH LOW LOW HIGH 1 ⁄2fxtal fxtal HIGH LOW HIGH HIGH STOP low fxtal HIGH HIGH X(1) X(1) STROBE fxtal LOW(2) X(1) X(1) X(1) STOP low 1 ⁄2fint(3) I/O circuitry The three I/O transceivers are identical. The state is HIGH for all I/O pins (i.e. I/O, I/OUC, AUX1, AUX1UC, AUX2 and AUX2UC). Pin I/O is referenced to VCC and pin I/OUC to VDD, thus ensuring proper operation in the event that VCC ≠ VDD. The first side on which a falling edge is detected becomes a master (input). An anti-latch circuitry first disables the detection of the falling edge on the other side, which becomes slave (output), see Fig.8. After a delay time td (between 50 and 400 ns), the logic 0 present on the master side is transferred on the slave side. When the input is back to HIGH level, a current booster is turned on during the delay td on the output side and then both sides are back to their idle state, ready to detect the next logic 0 on any side. In the event of a conflict, both lines may remain LOW until the software enables the lines to be HIGH. The anti-latch circuitry ensures that the lines do not remain LOW if both sides return HIGH, regardless of the prior conditions. The maximum frequency on the lines is approximately 200 kHz. When CS is HIGH, I/OUC, AUX1UC and AUX2UC are internally pulled-up to VDD with 20 kΩ resistors. When CS is LOW, I/OUC, AUX1UC and AUX2UC are permanently HIGH (with integrated 100 k Ω pull-up resistors connected to VDD). Fig.8 Master and slave signals. handbook, full pagewidth td MGD703 td td I/O I/OUC conflict idle |
Ähnliche Teilenummer - TDA8002CG |
|
Ähnliche Beschreibung - TDA8002CG |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |