Datenblatt-Suchmaschine für elektronische Bauteile
  German  ▼
ALLDATASHEETDE.COM

X  

ISL54221 Datenblatt(PDF) 8 Page - Intersil Corporation

Teilenummer ISL54221
Bauteilbeschribung  High-Speed USB 2.0 (480Mbps) Multiplexer
Download  13 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Hersteller  INTERSIL [Intersil Corporation]
Direct Link  http://www.intersil.com/cda/home
Logo INTERSIL - Intersil Corporation

ISL54221 Datenblatt(HTML) 8 Page - Intersil Corporation

Back Button ISL54221 Datasheet HTML 4Page - Intersil Corporation ISL54221 Datasheet HTML 5Page - Intersil Corporation ISL54221 Datasheet HTML 6Page - Intersil Corporation ISL54221 Datasheet HTML 7Page - Intersil Corporation ISL54221 Datasheet HTML 8Page - Intersil Corporation ISL54221 Datasheet HTML 9Page - Intersil Corporation ISL54221 Datasheet HTML 10Page - Intersil Corporation ISL54221 Datasheet HTML 11Page - Intersil Corporation ISL54221 Datasheet HTML 12Page - Intersil Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 8 / 13 page
background image
8
FN6820.0
December 16, 2008
all switches are OFF and the fault voltage is isolated from
the other side of the switch. When VDD is in the range of
2.7V to 5.5V the fault voltage will pass through to the output
of an active switch channel.
The HS1 channel switches are active (turned ON) whenever
the SEL voltage is logic”0”(Low) and the OE voltage is
logic”0”(Low).
The HS2 channel switches are active (turned ON) whenever
the SEL voltage is logic “1” (High) and the OE voltage is
logic “0” (Low).
ISL54221 Operation
The following will discuss using the ISL54221 the “Application
Block Diagram” on page 7.
POWER
The power supply connected at the VDD pin provides the
DC bias voltage required by the ISL54221 part for proper
operation. The ISL54221 can be operated with a VDD
voltage in the range of 2.7V to 5.5V. When used in a USB
application, the VDD voltage should be kept in the range of
3.0V to 5.5V to ensure you get the proper signal levels for
good signal quality.
A 0.01µF or 0.1µF decoupling capacitor should be
connected from the VDD pin to ground to filter out any power
supply noise from entering the part. The capacitor should be
located as close to the VDD pin as possible.
In a typical application, VDD will be in the range of 2.8V to
4.3V and will be connected to the battery or LDO of the
portable media device.
LOGIC CONTROL
The state of the ISL54221 device is determined by the
voltage at the SEL pin and the OE pin. SEL is only active
when the OE pin is logic “0” (Low). Refer to “Truth Table” on
page 2.
The ISL54221 logic pins are designed to minimize current
consumption when the logic control voltage is lower than the
VDD supply voltage. With VDD = 3.6V and logic pins at 1.4V
the part typically draws only 6.6µA. With VDD = 4.3V and
logic pins at 2.6V the part typically draws only 0.2µA. Driving
the logic pins to the VDD supply rail minimizes power
consumption.
The logic pins must be held High or Low and must not float.
Logic Control Voltage Levels
With VDD supply voltage in the range of 2.7V to 3.6V the
logic levels are:
OE = Logic “0” (Low) when VOE 0.5V
OE = Logic “1” (High) when VOE 1.4V
SEL = Logic “0” (Low) when VSEL 0.5V
SEL = Logic “1” (High) when VSEL 1.4V
With VDD supply voltage in the range of 4.3V to 5.5V the
logic levels are:
OE = Logic “0” (Low) when VOE 0.8V
OE = Logic “1” (High) when VOE 2.0V
SEL = Logic “0” (Low) when VSEL 0.8V
SEL = Logic “1” (High) when VSEL 2.0V
HSD1 USB Channel
If the SEL pin = Logic “0” and the OE pin = Logic “0”,
high-speed Channel 1 will be ON. The HSD1- and HSD1+
switches are ON and the HSD2- and HSD2+ switches are
OFF (high impedance).
When a computer or USB hub is plugged into the common
USB connector and channel one is active, a link will be
established between the USB 1 driver section of the media
player and the computer. The device will be able to transmit
and receive data from the computer at a data rate of
480Mbps.
HSD2 USB Channel
If the SEL pin = Logic “1” and the OE pin = Logic “0”,
high-speed Channel 2 will be ON. The HSD2- and HSD2+
switches are ON and the HSD1- and HSD1+ switches are
OFF (high impedance).
When a USB cable from a computer or USB hub is
connected at the common USB connector and the part has
Channel 2 active, a link will be established between the USB
2 driver section of the media player and the computer. The
device will be able to transmit and receive data from the
computer at a data rate of 480Mbps.
All Switches OFF Mode
If the SEL pin = Logic “0” or Logic “1” and the OE pin =
Logic “1”, all of the switches will turn OFF (high impedance).
The all OFF state can be used to switch between the two
USB sections of the media player. When disconnecting from
one USB device to the other USB device, you can
momentarily put the ISL54221 switch in the “all off” state in
order to get the computer to disconnect from the one device
so it can properly connect to the other USB device when that
channel is turned ON.
USB 2.0 VBUS Short Requirements
The USB specification in section 7.1.1 states a USB device
must be able to withstand a VBUS short to the D+ or D-
signal lines when the device is either powered off or
powered on for at least 24 hours. The ISL54220 part has
special fault protection circuitry to meet these short circuit
requirements.
The fault protection circuitry allows the signal pins (D-, D+,
HS1D-, HS1D+, HS2D-, HS2D+) to be driven up to 5.5V
while the VDD supply voltage is in the range of 0V to 5.5V. In
this overvoltage condition the part draws < 500µA of current
and causes no stress/damage to the IC.
ISL54221


Ähnliche Teilenummer - ISL54221

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
Intersil Corporation
ISL54221 INTERSIL-ISL54221 Datasheet
9Mb / 44P
   Providing high-performance solutions for every link in the signal chain
logo
Renesas Technology Corp
ISL54221 RENESAS-ISL54221 Datasheet
1Mb / 13P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54221IRUZ-T RENESAS-ISL54221IRUZ-T Datasheet
1Mb / 13P
   High-Speed USB 2.0 (480Mbps) Multiplexer
More results

Ähnliche Beschreibung - ISL54221

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
Renesas Technology Corp
ISL54220 RENESAS-ISL54220 Datasheet
1Mb / 18P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54223 RENESAS-ISL54223 Datasheet
1Mb / 13P
   High-Speed USB 2.0 (480Mbps) Multiplexer
May 27, 2009
logo
Intersil Corporation
ISL54222 INTERSIL-ISL54222 Datasheet
850Kb / 15P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54223 INTERSIL-ISL54223 Datasheet
780Kb / 13P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54220 INTERSIL-ISL54220 Datasheet
808Kb / 15P
   High-Speed USB 2.0 (480Mbps) Multiplexer
logo
Renesas Technology Corp
ISL54221 RENESAS-ISL54221 Datasheet
1Mb / 13P
   High-Speed USB 2.0 (480Mbps) Multiplexer
logo
Intersil Corporation
ISL54222A INTERSIL-ISL54222A_10 Datasheet
908Kb / 19P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54220 INTERSIL-ISL54220 Datasheet
841Kb / 18P
   High-Speed USB 2.0 480Mbps Multiplexer
ISL54222 INTERSIL-ISL54222_09 Datasheet
856Kb / 15P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54222A INTERSIL-ISL54222A Datasheet
891Kb / 17P
   High-Speed USB 2.0 (480Mbps) Multiplexer
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13


Datenblatt Download

Go To PDF Page


Link URL




Privatsphäre und Datenschutz
ALLDATASHEETDE.COM
War ALLDATASHEET hilfreich?  [ DONATE ] 

Über Alldatasheet   |   Werbung   |   Kontakt   |   Privatsphäre und Datenschutz   |   Linktausch   |   Hersteller
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com