 |
Datenblatt-Suchmaschine für elektronische Bauteile |
|
|
Datenblatt-Suchmaschine für elektronische Bauteile |
|
TMP320LF2401AVFS Datenblatt(PDF) 9 Page - Texas Instruments |
|
||||||||||||||||||||||||||||||
TMP320LF2401AVFS Datenblatt(HTML) 9 Page - Texas Instruments |
|
|
9 / 88 page  TMS320LF2401A, TMS320LC2401A DSP CONTROLLERS SPRS161K − MARCH 2001 − REVISED JULY 2007 9 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443 terminal functions Terminal Functions† TERMINAL DESCRIPTION NAME NO. DESCRIPTION RS 9 Device Reset (in) and Watchdog Reset (out). Device reset. RS causes the device to terminate execution and to set PC = 0. When RS is brought to a high level, execution begins at location 0x0000 of program memory. This pin is driven low by the DSP when a watchdog reset occurs. During watchdog reset, the RS pin will be driven low for the watchdog reset duration of 128 CLKIN cycles. The output buffer of this pin is an open-drain with an internal pullup (20 µA, typical). It is recommended that this pin be driven by an open-drain device. ( ↑) PDPINTA/IOPA0 32 Power drive protection input. When this pin is pulled low by an external event, an interrupt is generated and all PWM outputs go to high-impedance state. PDPINTA will keep PWM outputs in high-impedance state even when the DSP is not executing. ( ↑) NOTES: 1) Upon reset, the PDPINTA function is active, in addition to the GPIO function. If the IOPA0 function is desired, the PDPINTA function must be disabled. (This can be done by writing to bit 0 of the EVAIMRA register.) Otherwise, the PWM outputs could inadvertently be put into a high-impedance state when the IOPA0 pin is driven low. 2) When PDPINTA is used to “wake up” the DSP from LPM2, the pin should be held low for (98304 CLKIN + 12 CLKOUT) cycles. 3) This pin must be held high when on-chip boot ROM is invoked. PWM1/IOPA1 27 Compare/PWM output 1 or GPIO ( ↑) PWM2/IOPA2 28 Compare/PWM output 2 or GPIO ( ↑) PWM3/IOPA3 29 Compare/PWM output 3 or GPIO ( ↑) PWM4/IOPA4 10 Compare/PWM output 4 or GPIO ( ↑) PWM5/IOPA5 11 Compare/PWM output 5 or GPIO ( ↑) PWM6/IOPA6 12 Compare/PWM output 6 or GPIO ( ↑) T2PWM/XINT1/IOPB0 31 Upon reset, this pin comes up as XINT1/IOPB0 pin. To enable the XINT1 function, the appropriate bit in the XINT1CR register must be set. No special configuration sequence is needed to use this pin as a GPIO. However, a write to the PADATDIR register is necessary to configure this pin as a general-purpose output. Configuration of this pin as T2PWM is achieved by writing a one to bit 8 of the MCRA register. Note that the value of bit 8 in the MCRA register does not affect the XINT1 functionality of this pin. The XINT1 function is enabled/disabled by the value written into the XINT1CR register and is independent of the value written in bit 8 in the MCRA register. ( ↑) XINT2/ADCSOC/CAP1/ IOPA7/CLKOUT 22 Upon reset, this pin can be configured as any one of the following: XINT2, ADCSOC, CAP1, or IOPA7. To configure this pin for XINT2 function, the appropriate bit in the XINT2CR register must be set. To configure this pin for ADCSOC function, the appropriate bit in the ADCTRL2 register must be set. To configure this pin for CAP1 function, the appropriate bits in the CAPCONA register must be configured. To summarize, the XINT2, ADCSOC, and CAP1 functions are enabled at the respective peripheral level. No special configuration sequence is needed to use this pin as a GPIO. However, a write to the PADATDIR register is necessary to configure this pin as a general-purpose output. This pin can also function as the CPU clock output. This is achieved by writing a one to bit 7 of the MCRA register. When CLKOUT is chosen, the internal logic for the XINT2, ADCSOC, and CAP1 sees the pin as a “1”. ( ↑) † Bold face type indicates function of the device pin after reset. ‡ It is highly recommended that VCCA be isolated from the digital supply voltage (and VSSA from digital ground) to maintain the specified accuracy and improve the noise immunity of the ADC. § TDI is MUXed with digital output, not digital I/O. ¶ Pin 26 is VCCP on LF2401A and is a No Connect (NC) on LC2401A. LEGEND: ↑ − Internal pullup ↓ − Internal pulldown (Typical active pullup/pulldown value is ±20 µA.) NOTE: On the target hardware, pins 13 and 14 (EMU0/EMU1) of the JTAG header must be pulled high. |
Ähnliche Teilenummer - TMP320LF2401AVFS |
|
Ähnliche Beschreibung - TMP320LF2401AVFS |
|
|
Link URL |
| Privatsphäre und Datenschutz |
| ALLDATASHEETDE.COM |
| War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
German ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
