Datenblatt-Suchmaschine für elektronische Bauteile
  German  ▼
ALLDATASHEETDE.COM

X  

ISL54222A Datenblatt(PDF) 10 Page - Intersil Corporation

Teilenummer ISL54222A
Bauteilbeschribung  High-Speed USB 2.0 (480Mbps) Multiplexer
Download  19 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Hersteller  INTERSIL [Intersil Corporation]
Direct Link  http://www.intersil.com/cda/home
Logo INTERSIL - Intersil Corporation

ISL54222A Datenblatt(HTML) 10 Page - Intersil Corporation

Back Button ISL54222A_10 Datasheet HTML 6Page - Intersil Corporation ISL54222A_10 Datasheet HTML 7Page - Intersil Corporation ISL54222A_10 Datasheet HTML 8Page - Intersil Corporation ISL54222A_10 Datasheet HTML 9Page - Intersil Corporation ISL54222A_10 Datasheet HTML 10Page - Intersil Corporation ISL54222A_10 Datasheet HTML 11Page - Intersil Corporation ISL54222A_10 Datasheet HTML 12Page - Intersil Corporation ISL54222A_10 Datasheet HTML 13Page - Intersil Corporation ISL54222A_10 Datasheet HTML 14Page - Intersil Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 10 / 19 page
background image
10
FN6902.1
February 4, 2010
in the range of 1.8V to 3.3V, the fault voltage will pass
through to the output of an active switch channel.
During the fault condition normal operation is not
guaranteed until the fault is removed. See the following
“USB 2.0 VBUS Short Requirements” on page 10.
The HS1 channel switches are active (turned ON)
whenever the SEL voltage is logic”0”(Low) and the OE
voltage is logic”0”(Low).
The HS2 channel switches are active (turned ON)
whenever the SEL voltage is logic “1” (High) and the OE
voltage is logic “0” (Low).
ISL54222A Operation
The following will discuss using the ISL54222A shown in
the “Application Block Diagram” on page 9.
POWER
The power supply connected at the VDD pin provides the
DC bias voltage required by the ISL54222A part for
proper operation. The ISL54222A can be operated with a
VDD voltage in the range of 1.8V to 3.3V.
A 0.01µF or 0.1µF decoupling capacitor should be
connected from the VDD pin to ground to filter out any
power supply noise from entering the part. The capacitor
should be located as close to the VDD pin as possible.
LOGIC CONTROL
The state of the ISL54222A device is determined by the
voltage at the SEL pin and the OE pin. SEL is only active
when the OE pin is logic “0” (Low). Refer to “Truth Table”
on page 2.
The ISL54222A logic pins are designed to minimize
current consumption when the logic control voltage is
lower than the VDD supply voltage. With VDD = 3.3V and
logic pins at 1.4V, the part typically draws only 6.6µA.
With VDD = 1.8V and logic pins at 1.4V, the part typically
draws only 0.2µA. Driving the logic pins to the VDD
supply rail minimizes power consumption. The logic pins
must be driven High or Low and must not float.
LOGIC CONTROL VOLTAGE LEVELS
With VDD supply voltage in the range of 1.8V to 3.3V the
logic levels are:
OE = Logic “0” (Low) when VOE 0.5V
OE = Logic “1” (High) when VOE 1.4V
SEL = Logic “0” (Low) when VSEL 0.5V
SEL = Logic “1” (High) when VSEL 1.4V
HSD1 USB CHANNEL
If the SEL pin = Logic “0” and the OE pin = Logic “0”,
high-speed Channel 1 will be ON. The HSD1- and HSD1+
switches are ON and the HSD2- and HSD2+ switches are
OFF (high impedance).
When a computer or USB hub is plugged into the
common USB connector and Channel 1 is active, a link
will be established between the USB 1 transceiver section
of the media player and the computer. The device
transceiver 1 will be able to transmit and receive data
from the computer.
HSD2 USB Channel
If the SEL pin = Logic “1” and the OE pin = Logic “0”,
high-speed Channel 2 will be ON. The HSD2- and HSD2+
switches are ON and the HSD1- and HSD1+ switches are
OFF (high impedance).
When a USB cable from a computer or USB hub is
connected at the common USB connector and the part
has Channel 2 active, a link will be established between
the USB 2 transceiver section of the media player and
the computer. The device transceiver 2 will be able to
transmit and receive data from the computer.
ALL SWITCHES OFF/LOW POWER MODE
If the SEL pin = Logic “0” or Logic “1” and the OE
pin = Logic “1”, all of the switches will turn OFF (high
impedance) and the part will be put in a low power
mode. In this mode the part draws only 1.5µA (max) of
current across the operating temperature range.
The all OFF state can be used to switch between the two
USB sections of the media player. When disconnecting
from one USB device to the other USB device, you can
momentarily put the ISL54222A switch in the “all off”
state in order to get the computer to disconnect from the
one device so it can properly connect to the other USB
device when that channel is turned ON.
USB 2.0 VBUS Short Requirements
The USB 2.0 specification in chapter 7, section 7.1.1
states a USB device must be able to withstand a VBUS
short to the D+ or D- signal lines when the device is
either powered off or powered on for at least 24 hours.
The ISL54222A part has special fault protection circuitry
to meet these short circuit requirements.
The fault protection circuitry allows the signal pins
(D-, D+, HSD1-, HSD1+, HSD2-, HSD2+) to be driven
up to 5.5V while the VDD supply voltage is in the range of
0V to 3.3V. In this overvoltage condition, the part draws
< 300µA of IDD current and causes no stress or damage
to the IC.
In addition, when VDD is at 0V (ground), all switches are
OFF and the shorted VBUS voltage is isolated from the
other side of the switch.
When VDD is in the range of 1.8V to 3.3V, the shorted
VBUS voltage will pass through to the output of an active
(turned ON) switch channel but not through a turned OFF
channel. Any components connected on the active
channel must be able to withstand the overvoltage
condition.
Note: During the fault condition, normal operation of the
USB channel is not guaranteed until the fault condition is
removed.
ISL54222A


Ähnliche Teilenummer - ISL54222A_10

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
Intersil Corporation
ISL54222AIRTZ INTERSIL-ISL54222AIRTZ Datasheet
891Kb / 17P
   High-Speed USB 2.0 (480Mbps) Multiplexer
logo
Renesas Technology Corp
ISL54222AIRTZ RENESAS-ISL54222AIRTZ Datasheet
1Mb / 19P
   High-Speed USB 2.0 (480Mbps) Multiplexer
logo
Intersil Corporation
ISL54222AIRTZ-T INTERSIL-ISL54222AIRTZ-T Datasheet
891Kb / 17P
   High-Speed USB 2.0 (480Mbps) Multiplexer
logo
Renesas Technology Corp
ISL54222AIRTZ-T RENESAS-ISL54222AIRTZ-T Datasheet
1Mb / 19P
   High-Speed USB 2.0 (480Mbps) Multiplexer
logo
Intersil Corporation
ISL54222AIRU1Z-T INTERSIL-ISL54222AIRU1Z-T Datasheet
891Kb / 17P
   High-Speed USB 2.0 (480Mbps) Multiplexer
More results

Ähnliche Beschreibung - ISL54222A_10

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
Renesas Technology Corp
ISL54220 RENESAS-ISL54220 Datasheet
1Mb / 18P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54223 RENESAS-ISL54223 Datasheet
1Mb / 13P
   High-Speed USB 2.0 (480Mbps) Multiplexer
May 27, 2009
logo
Intersil Corporation
ISL54222 INTERSIL-ISL54222 Datasheet
850Kb / 15P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54223 INTERSIL-ISL54223 Datasheet
780Kb / 13P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54220 INTERSIL-ISL54220 Datasheet
808Kb / 15P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54221 INTERSIL-ISL54221 Datasheet
741Kb / 13P
   High-Speed USB 2.0 (480Mbps) Multiplexer
logo
Renesas Technology Corp
ISL54221 RENESAS-ISL54221 Datasheet
1Mb / 13P
   High-Speed USB 2.0 (480Mbps) Multiplexer
logo
Intersil Corporation
ISL54220 INTERSIL-ISL54220 Datasheet
841Kb / 18P
   High-Speed USB 2.0 480Mbps Multiplexer
ISL54222 INTERSIL-ISL54222_09 Datasheet
856Kb / 15P
   High-Speed USB 2.0 (480Mbps) Multiplexer
ISL54222A INTERSIL-ISL54222A Datasheet
891Kb / 17P
   High-Speed USB 2.0 (480Mbps) Multiplexer
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19


Datenblatt Download

Go To PDF Page


Link URL




Privatsphäre und Datenschutz
ALLDATASHEETDE.COM
War ALLDATASHEET hilfreich?  [ DONATE ] 

Über Alldatasheet   |   Werbung   |   Kontakt   |   Privatsphäre und Datenschutz   |   Linktausch   |   Hersteller
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com