Datenblatt-Suchmaschine für elektronische Bauteile |
|
LA70100M Datenblatt(PDF) 10 Page - Sanyo Semicon Device |
|
LA70100M Datenblatt(HTML) 10 Page - Sanyo Semicon Device |
10 / 16 page LA70100M No.7204-10/16 During a period when the color signal processing is left untouched (for about 700 µs from the start of vertical sync signal), center frequency of BELL filter is automatically adjusted. MODE CONTROL sets each BELL/A-BELL filter into VCO mode after vertical sync signal is input, then the OSC oscillates at 4.3MHz or 1.1MNz. Oscillation output is divided respectively by a programmable divider and outputs the timing pulse that corresponds to oscillation frequency with control logic. This pulse is compared with the timing pules acquired by dividing 4.43MHz CLK and generates UP or DOWN CLK corresponding to the amount of discrepancies for oscillation frequency 4.286MHz/1.0715MHz. That is input to UP/DOWN counter to increase and decrease the counter value. When ENABLE pulse is generated the outputs D0 to D5 are rewritten, and the control voltage varies so that the oscillation frequency approach 4.286MHz/1.0715MHz. This operation repeats whenever the vertical sync signal is input and stops when the frequency difference becomes to a specified value ( ±43kHz / ±10.7kHz ). (9) SECAM The color signal with the amplitude limited by limiting circuit varies the phase according to the signal frequency after it passes through a 4.3MHz BPF. DC voltage according to the phase can be acquired by shifting this output phase by further 90 ° and inputting it to a phase detector with the original signal. The characteristic of the output of a phase detector is as shown in the figure 9 (b), as the voltage limiting circuit operates at S/H-3 in order to prevent the malfunction caused by unwanted signals. This limiting circuit voltage is the phase detector output DC voltage to which the signals of 4.286MHz VCO is input used on BELL filter automatic adjusting circuit. Then it is possible to operate the limiting circuit exactly at a frequency more than 4.286 MHz and to prevent the false discrimination during MESECAM signal input. After that, input to two sample & hold circuits, the sampling pulse is shown like pulses correspond to BGP of NTSC and PAL generated every 1H as SP1 and SP2 in figure 9 (b). The SECAM color signal has ID signals of 4.25MHz and 4.40625MHz generated every 1H on the part that corresponds to this BGP, each phase detection output causes the level difference as V1, V2 in figure 9 (b). When this difference is sampled by SP1 and SP2 the waveform becomes as VS1 and VS2 in the figure 9 (b), and when it is hold by external capacitor it becomes as V1 and V2. Input to a comparator after detecting the difference of these two voltages, smoothing it to stable with the external capacitor connected to Pin 27. In addition, applying more than 1V DC voltage to Pin 30 allows the amplification of the level difference to be varied. When the smooth value of V1-V2 exceeds 3.5V, SECAM signal is detected with a high-level output from the Pin 28. This discrimination circuit uses a rule that the output of a phase detector differs every 1H as shown in the figure 9 (b) (c) to detect a SECAM signal. PAL signal always outputs high since its burst is constant and doesn’t vary phase detection output. COMP LOGIC Vref CTL SECAM DET OUT S/H-3 4.3MHz BPF 90 DEG PHASE DET LIM from MAIN SIGNAL LINE S/H-2 S/H-1 BELL ADJUST PULSE 28 SAMPLE HOLD PULSE 27 25 21 SENS CONTROL 30 SAMPLE HOLD PULSE 26 S/H-2 Fig.9(a) S/H-3 + DET S/H-1 + 128 µs SP1 SP2 SP3 Same as ESOSC at fig.8 (b) VS1 VS2 V1 V2 Chroma signal Fig.9 (b) 4.25MHz (4.28MHz) 4.40625MHz V1 V2 VL Frequency Voltage Fig.9 (c) C.sync VD ENOSC 4.3MHz/1.1MHz OSC ENABLE Fig.8 (b) 700 µs |
Ähnliche Teilenummer - LA70100M_07 |
|
Ähnliche Beschreibung - LA70100M_07 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |