Datenblatt-Suchmaschine für elektronische Bauteile
  German  ▼
ALLDATASHEETDE.COM

X  

AD8170AR-REEL Datenblatt(PDF) 3 Page - Analog Devices

Teilenummer AD8170AR-REEL
Bauteilbeschribung  250 MHz, 10 ns Switching Multiplexers w/Amplifier
Download  16 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Hersteller  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

AD8170AR-REEL Datenblatt(HTML) 3 Page - Analog Devices

  AD8170AR-REEL Datasheet HTML 1Page - Analog Devices AD8170AR-REEL Datasheet HTML 2Page - Analog Devices AD8170AR-REEL Datasheet HTML 3Page - Analog Devices AD8170AR-REEL Datasheet HTML 4Page - Analog Devices AD8170AR-REEL Datasheet HTML 5Page - Analog Devices AD8170AR-REEL Datasheet HTML 6Page - Analog Devices AD8170AR-REEL Datasheet HTML 7Page - Analog Devices AD8170AR-REEL Datasheet HTML 8Page - Analog Devices AD8170AR-REEL Datasheet HTML 9Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 3 / 16 page
background image
–3–
REV. 0
AD8170/AD8174
AD8170A/AD8174A
Parameter
Conditions
Min
Typ
Max
Units
INPUT CHARACTERISTICS
Input Resistance
(+) Switch Input
1.7
M
(–) Buffer Input
100
Input Capacitance
Channel Enabled (R Package)
1.1
pF
Channel Disabled (R Package)
1.1
pF
Input Voltage Range
±3.3
V
Input Common-Mode Rejection Ratio
+CMRR,
∆V
CM = 1 V
51
56
dB
–CMRR,
∆V
CM = 1 V
50
52
dB
OUTPUT CHARACTERISTICS
Output Voltage Swing
RL = 1 kΩ, TMIN–TMAX
±4.0
±4.26
V
RL = 150 Ω, TMIN–TMAX
±3.5
±4.0
V
Output Current
RL = 10 Ω
50
mA
Short Circuit Current
180
mA
Output Resistance
Enabled
10
m
Disabled (AD8174)
10
M
Output Capacitance
Disabled (AD8174)
7.5
pF
POWER SUPPLY
Operating Range
±4
±6V
Power Supply Rejection Ratio
+PSRR
+VS = +4.5 V to +5.5 V, –VS = –5 V
58
66
dB
TMIN–TMAX
55
dB
Power Supply Rejection Ratio
–PSRR
–VS = –4.5 V to –5.5 V, +VS= +5 V
52
58
dB
TMIN–TMAX
50
dB
Quiescent Current
All Channels “ON”, TMIN–TMAX
8.7/9.7
11/13
mA
AD8174 Disabled, TMIN–TMAX
4.1
5
mA
AD8174 Shutdown, TMIN–TMAX
1.5
2.5
mA
OPERATING TEMPERATURE RANGE
–40
+85
°C
NOTES
1Shutdown (SD) and ENABLE pins are grounded (AD8174). IN0 (or IN2) = +0.5 V dc, IN1 (or IN3) = –0.5 V dc. SELECT (A0 or A1 for AD8174) input is
driven with 0 V to +5 V pulse. Measure transition time from 50% of SELECT (A0 or A1) input value (+2.5 V) and 10% (or 90%) of the total output voltage transi-
tion from IN0 (or IN2) channel voltage (+0.5 V) to IN1 (or IN3 = –0.5 V) or vice versa.
2AD8174 only. Shutdown (SD) pin is grounded. ENABLE pin is driven with 0 V to +5 V pulse (5 ns rise and fall times). State of A0 and A1 logic inputs determines
which channel is activated (i.e., if A0 = Logic 0 and A1 = Logic 1, then IN2 input is selected). Set IN0 (or IN2) = +0.5 V dc, IN1 (or IN3) = –0.5 V dc, and mea-
sure transition time from 50% of ENABLE pulse (+2.5 V) to 90% of the total output voltage change. In Figure 5,
∆t
OFF is the disable time,
∆t
ON is the enable time.
3AD8174 only. ENABLE pin is grounded. Shutdown (SD) pin is driven with 0 V to +5 V pulse (5 ns rise and fall times). State of A0 and A1 logic inputs determines
which channel is activated (i.e., if A0 = Logic 1 and A1 = Logic O, then IN1 input is selected). Set IN0 (or IN2) = +0.5 V dc, IN1 (or IN3) = –0.5 V dc, and mea-
sure transition time from 50% of SD pulse (+2.5 V) to 90% of the total output voltage change. In Fig ure 6,
∆t
OFF is the shutdown assert time ,
∆t
ON is the shutdown
release time.
4All inputs are grounded. SELECT (A0 or A1 for AD8174) input is driven with 0 V to +5 V pulse. The outputs are monitored. Speeding the edges of the SELECT
(A0 or A1) pulse increases the glitch magnitude due to coupling via the ground plane.
5Bandwidth of the multiplexer is dependent upon the resistor feedback network. Refer to Table III for recommended feedback component values, which give the best
compromise between a wide and a flat frequency response.
6Select input(s) that is (are) not being driven (i.e., if SELECT is Logic 1, activated input is IN1; in AD8174, if A0 = Logic 0, A1 = Logic 1, activated input is IN2).
Drive all other inputs with VIN = 0.707 V rms, and monitor output at f = 5 MHz and 30 MHz; RL = 100
Ω (see Figure 13).
7AD8174 only. Shutdown (SD) pin is grounded. Mux is disabled, (i.e., ENABLE = Logic 1) and all inputs are driven simultaneously with V
IN = 0.354 V rms. Out-
put is monitored at f = 5 MHz and 30 MHz; RL = 100
Ω. In this mode, the output impedance of the disabled mux is very high (typ 10 MΩ), and the signal couples
across the package; the load impedance and the feedback network determine the crosstalk. For instance, in a closed-loop gain of +1, r OUT
10 M
Ω, in a gain of +2
(RF = RG = 549
Ω), r
OUT = 1.1 k
Ω (see Figure 14).
8AD8174 only. ENABLE pin is grounded. Mux is shutdown (i.e., SD = Logic 1), and all inputs are driven simultaneously with V
IN = 0.354 V rms. Output is moni-
tored at f = 5 MHz and 30 MHz; RL = 100
Ω. (see Figure 14). The mux output impedance in shutdown mode is the same as the disabled mux output impedance.
9For Gain Accuracy expression, refer to Equation 4.
Specifications subject to change without notice.
Table I. AD8170 Truth Table
SELECT
VOUT
0
IN0
1
IN1
Table II. AD8174 Truth Table
A0
A1
ENABLE
SD
VOUT
0
0
0
0
IN0
1
0
0
0
IN1
0
1
0
0
IN2
1
1
0
0
IN3
X
X
1
0
HIGH Z, IS = 4.1 mA
X
X
X
1
HIGH Z, IS = 1.5 mA


Ähnliche Teilenummer - AD8170AR-REEL

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
Analog Devices
AD8170AR-REEL AD-AD8170AR-REEL Datasheet
476Kb / 16P
   250 MHz, 10 ns Switching Multiplexers w/Amplifier
REV. 0
More results

Ähnliche Beschreibung - AD8170AR-REEL

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
Analog Devices
AD8174ARZ AD-AD8174ARZ Datasheet
476Kb / 16P
   250 MHz, 10 ns Switching Multiplexers w/Amplifier
REV. 0
AD8170ARZ AD-AD8170ARZ Datasheet
476Kb / 16P
   250 MHz, 10 ns Switching Multiplexers w/Amplifier
REV. 0
AD8180 AD-AD8180_15 Datasheet
256Kb / 12P
   10 ns Switching Multiplexers
REV. B
AD8182 AD-AD8182_15 Datasheet
256Kb / 12P
   10 ns Switching Multiplexers
REV. B
AD8180ARZ AD-AD8180ARZ Datasheet
256Kb / 12P
   750 MHz, 3.8 mA 10 ns Switching Multiplexers
REV. B
AD8180 AD-AD8180 Datasheet
253Kb / 12P
   750 MHz, 3.8 mA 10 ns Switching Multiplexers
REV. B
AD8182ARZ AD-AD8182ARZ Datasheet
256Kb / 12P
   750 MHz, 3.8 mA 10 ns Switching Multiplexers
REV. B
logo
M/A-COM Technology Solu...
A83-1 MA-COM-A83-1 Datasheet
1Mb / 2P
   Cascadable Amplifier 10 to 250 MHz
logo
Tyco Electronics
A70 MACOM-A70_1 Datasheet
369Kb / 2P
   Cascadable Amplifier 10 to 250 MHz
logo
M/A-COM Technology Solu...
A70-1 MA-COM-A70-1 Datasheet
1Mb / 2P
   Cascadable Amplifier 10 to 250 MHz
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16


Datenblatt Download

Go To PDF Page


Link URL




Privatsphäre und Datenschutz
ALLDATASHEETDE.COM
War ALLDATASHEET hilfreich?  [ DONATE ] 

Über Alldatasheet   |   Werbung   |   Kontakt   |   Privatsphäre und Datenschutz   |   Linktausch   |   Hersteller
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com