 |
Datenblatt-Suchmaschine für elektronische Bauteile |
|
|
Datenblatt-Suchmaschine für elektronische Bauteile |
|
TMP102AIDRLT Datenblatt(PDF) 8 Page - Texas Instruments |
|
|
||||||||||||||||||||||||||||||
TMP102AIDRLT Datenblatt(HTML) 8 Page - Texas Instruments |
|
|
8 / 22 page  Measured Temperature T HIGH T LOW Device ALERTPIN (ComparatorMode) POL=0 Device ALERTPIN (InterruptMode) POL=0 Device ALERTPIN (ComparatorMode) POL=1 Device ALERTPIN (InterruptMode) POL=1 Read Read Time Read Startup Startof Conversion Delay (1) 26ms 26ms TMP102 SBOS397C – AUGUST 2007 – REVISED OCTOBER 2012 www.ti.com After power-up or general-call reset, the TMP102 immediately starts a conversion, as shown in Figure 9. The first result is available after 26ms (typical). The active quiescent current during conversion is 40 μA (typical at +27°C). The quiescent current during delay is 2.2 μA (typical at +27°C). (1) Delay is set by CR1 and CR0. Figure 9. Conversion Start SHUTDOWN MODE (SD) The Shutdown mode bit saves maximum power by shutting down all device circuitry other than the serial Figure 10. Output Transfer Function Diagrams interface, reducing current consumption to typically less than 0.5 μA. Shutdown mode is enabled when the SD bit is '1'; the device shuts down when current FAULT QUEUE (F1/F0) conversion is completed. When SD is equal to '0', the A fault condition exists when the measured device maintains a continuous conversion state. temperature exceeds the user-defined limits set in the THIGH and TLOW registers. Additionally, the number of THERMOSTAT MODE (TM) fault conditions required to generate an alert may be programmed using the fault queue. The fault queue is The Thermostat mode bit indicates to the device provided to prevent a false alert as a result of whether to operate in Comparator mode (TM = 0) or environmental noise. The fault queue requires Interrupt mode (TM = 1). For more information on consecutive fault measurements in order to trigger comparator and interrupt modes, see the High- and the alert function. Table 9 defines the number of Low-Limit Registers section. measured faults that may be programmed to trigger an alert condition in the device. For THIGH and TLOW POLARITY (POL) register format and byte order, see the High- and The Polarity bit allows the user to adjust the polarity Low-Limit Registers section. of the ALERT pin output. If POL = 0, the ALERT pin will be active low, as shown in Figure 10. For POL = Table 9. TMP102 Fault Settings 1, the ALERT pin will be active high, and the state of F1 F0 CONSECUTIVE FAULTS the ALERT pin is inverted. 0 0 1 0 1 2 1 0 4 1 1 6 8 Submit Documentation Feedback Copyright © 2007–2012, Texas Instruments Incorporated Product Folder Links: TMP102 |
Ähnliche Teilenummer - TMP102AIDRLT |
|
Ähnliche Beschreibung - TMP102AIDRLT |
|
|
|
Link URL |
| Privatsphäre und Datenschutz |
| ALLDATASHEETDE.COM |
| War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
German ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
