Datenblatt-Suchmaschine für elektronische Bauteile |
|
HCPL-2300 Datenblatt(PDF) 8 Page - AVAGO TECHNOLOGIES LIMITED |
|
HCPL-2300 Datenblatt(HTML) 8 Page - AVAGO TECHNOLOGIES LIMITED |
8 / 14 page 8 Notes: 1. Bypassing the power supply line is required with a 0.1 µF ceramic disc capacitor adjacent to each optocoupler as illustrated in Figure 19. The power supply bus for the optocoupler(s) should be separate from the bus for any active loads, otherwise a larger value of bypass capacitor (up to 0.5 µF) may be needed to suppress regenerative feedback via the power supply. 2. Peaking circuits may produce transient input currents up to 100 mA, 500 ns maximum pulse width, provided average current does not exceed 5 mA. 3. Device considered a two terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together. 4. The t PLH propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.5 V point on the trailing edge of the output pulse. 5. The t PHL propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.5 V point on the leading edge of the output pulse. 6. CM H is the maximum tolerable rate of rise of the common mode voltage to assure that the output will remain in a high logic state (i.e., V OUT > 2.0 V). 7. CM L is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state (i.e., V OUT < 0.8 V). 8. C P is the peaking capacitance. Refer to test circuit in Figure 8. 9. In accordance with UL 1577, each optocoupler is momentary with- stand proof tested by applying an insulation test voltage ≥4500 Vrms for 1 second (leakage detection current limit, I I-O ≤ 5 µA). This test is performed before the 100% production test for partial dis- charge (Method b) shown in the IEC/EN/DIN EN 60747-5-5 Insula- tion Characteristics Table, if applicable. Figure 3. Typical output voltage vs. forward input current vs. temperature. Figure 2. Typical input diode forward charac- teristics. Figure 4. Typical logic high output current vs. temperature. Package Characteristics For -40°C ≤T A ≤85°C, unless otherwise specified. All typicals at TA = 25°C. Parameter Symbol Min. Typ. Max. Units Test Conditions Fig. Notes Input-Output Momentary V ISO 3750 V rms RH ≤ 50%, t = 1 min, 3, 9 Withstand Voltage* T A = 25°C Resistance, Input-Output R I-O 1012 Ω V I-O = 500 V 3 Capacitance, Input-Output C I-O 0.6 pF f = 1 MHz 3 *The Input-Output MomentaryWithstandVoltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-5 Insulation Characteristics Table (if applicable), your equipment level safety specification, or Avago Application Note 1074, “Optocoupler Input-Output Endurance Voltage.” |
Ähnliche Teilenummer - HCPL-2300_13 |
|
Ähnliche Beschreibung - HCPL-2300_13 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |