Datenblatt-Suchmaschine für elektronische Bauteile |
|
ADM9240ARU Datenblatt(PDF) 6 Page - Analog Devices |
|
ADM9240ARU Datenblatt(HTML) 6 Page - Analog Devices |
6 / 22 page ADM9240 –6– REV. 0 GENERAL DESCRIPTION The ADM9240 is a complete system hardware monitor for microprocessor-based systems. The device communicates with the system via a serial System Management Bus. The serial bus controller has two hardwired address lines for device selection (Pin 1 and Pin 2), a serial data line for reading and writing addresses and data (Pin 3), and an input line for the serial clock (Pin 4). All control and programming functions of the ADM9240 are performed over the serial bus. An on-chip analog-to-digital converter with six multiplexed analog inputs measures power supply voltages (+12 V, +5 V, +3.3 V, +2.5 V—Pins 15 to 18) and processor core voltages (+VCCP1 and +VCCP2—Pins 19 and 14). The ADC also accepts input from an on-chip bandgap temperature sensor that moni- tors system ambient temperature. Two count inputs (Pins 5 and 6) are provided for monitoring the speed of fans with tachometer outputs. To accommodate fans with different speeds and different tacho outputs, a divisor of 1, 2, 4 or 8 can be programmed into the counter. Five digital inputs (VID4 to VID0—Pins 20 to 24) read the processor Voltage ID code, while a chassis intrusion input (Pin 7) is provided to detect unauthorized tampering with the equipment. When the ADM9240 monitoring sequence is started, it cycles sequentially through the measurement of analog inputs and the temperature sensor, while at the same time the fan speed inputs are independently monitored. Measured values from these in- puts are stored in value registers. These can be read out over the serial bus, or can be compared with programmed limits stored in the limit registers. The results of out-of-limit comparisons are stored in the interrupt status registers and will generate an inter- rupt on the INT line (Pin 10). Any or all of the Interrupt Status Bits can be masked by appro- priate programming of the Interrupt Mask Register. A RESET input/output (Pin 12) is provided. Pulling this pin low will reset all ADM9240 internal registers to default values. The ADM9240 can also be programmed to give a low-going 20 ms reset pulse at this pin. The ADM9240 contains an on-chip, 8-bit digital-to-analog converter with an output range of zero to 1.25 V (Pin 11). This is typically used to implement a temperature-controlled fan by controlling the speed of a fan dependent upon the temperature measured by the on-chip temperature sensor. Testing of board level connectivity is simplified by providing a NAND tree test function. The AOUT (Pin 11) also doubles as a NAND test input, while Pin 1 doubles as a NAND tree output. INTERNAL REGISTERS OF THE ADM9240 A brief description of the ADM9240’s principal internal regis- ters is given below. More detailed information on the function of each register is given in Tables V to XVII. Configuration Register: Provides control and configuration. Serial Address Register: Stores the serial bus address of the ADM9240. Address Pointer Register: Contains the address that selects one of the other internal registers. When writing to the ADM9240, the first byte of data is always a register address, which is written to the Address Pointer Register. Interrupt (INT) Status Registers: Two registers to provide status of each Interrupt event. Interrupt (INT) Mask Registers: Allow masking of indi- vidual Interrupt sources. Temperature Configuration Register: The configuration of the temperature interrupt is controlled by the lower three bits of this register. VID/Fan Divisor Registers: The status of the VID0 to VID4 pins of the processor can be written to and read from these registers. Divisor values for fan-speed measurement are also stored in one of these registers. Value and Limit Registers: The results of analog voltage inputs, temperature and fan speed measurements are stored in these registers, along with their limit values. Analog Output Register: The code controlling the analog output DAC is stored in this register. Chassis Intrusion Clear Register: A signal latched on the chassis intrusion pin can be cleared by writing to this register. |
Ähnliche Teilenummer - ADM9240ARU |
|
Ähnliche Beschreibung - ADM9240ARU |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |