Datenblatt-Suchmaschine für elektronische Bauteile |
|
CBC-EVAL-09 Datenblatt(PDF) 4 Page - Cymbet Corporation |
|
CBC-EVAL-09 Datenblatt(HTML) 4 Page - Cymbet Corporation |
4 / 15 page CBC-EVAL-09 EnerChip EP Universal EH Eval Kit ©2013 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com DS-72-13 Rev G Page 4 of 15 EVAL-09 Module Connector and Test Point Explanations The purpose and use of the connectors identified in Figure 3 and in the previous tables are: J1, J2, J8, J11, J13, J14 Connectors - not user accessible. J3 Connector - EnerChip EP pins 1-19 probe points and access vias. J4 Connector - EnerChip EP pins 20-38 probe points and access vias. J5, J6 Connectors - EVAL-09 debug interface connectors for development system access. Contact Cymbet Applications Engineering for additional details if required . J7 Connector - Bypass diode circular pad trace to select an optional external rechargeable lithium battery with 4.1V charging voltage. J9 Connector - Six pin right angle connector for serial port, Vout and Ground. Normally used for connection to TI eZ430-RF2500 wireless end device or another target system. J10 Connector - Five pin vertical connector for user access to serial port, Vout and Ground. J12 Connector - Access vias for an optional external rechargeable lithium battery with 4.1V charging voltage. J15 Connector - High Voltage DC Input from EH Transducer such as a thermoelectric generator (TEG). J16 Connector - High Voltage AC Input 1 normally used by a piezoelectric EH transducer. J17 Connector - High Voltage AC Input 2 normally used by a piezoelectric EH transducer . J18 Connector - Low voltage DC Input normally used by a photovoltaic cell. J19 Connector - Low voltage AC Input normally used by a thermoelectric generator or electromagnetic generator. Cable Assembly - A 5-conductor cable with a header connector at each end is provided with CBC-EVAL-09 to facilitate connection between the J5 connector and a 5-pin header on the user’s board. TP1 - the output of the boost converter or FLYBACK converter capacitor. Typical value is 4.06V. TP2 - EPVCC - Voltage used to power the CBC915 device should be 3.6V TP3, TP3, TP5 - Ground TP6 – VCAP – voltage of the output capacitor should be 3.6V TP7 – VOUT – output voltage to the target system should be 3.6V TP8 – VBAT – output of battery cut-off circuit should be 4.06V TP9 – VEC – EnerChip output voltage feeding battery cutoff circuit should be in the range of 4.06VDC to 3.0VDC. Caution: do not leave voltmeter or scope probes attached to this TP. Will discharge EnerChip. TP10 – HV V In – DC voltage from the HV DC In or HV AC1 IN or HV AC2 IN ports TP11 – V In – DC voltage from the DC In or AC1 IN ports |
Ähnliche Teilenummer - CBC-EVAL-09 |
|
Ähnliche Beschreibung - CBC-EVAL-09 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |