Datenblatt-Suchmaschine für elektronische Bauteile |
|
LM20333 Datenblatt(PDF) 2 Page - Texas Instruments |
|
|
LM20333 Datenblatt(HTML) 2 Page - Texas Instruments |
2 / 29 page VIN 1 FB SS/TRK SW VIN GND AGND SW EN VIN PGOOD COMP EP VCC 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 SW GND GND SW VIN SYNC BOOT LM20333 SNVS558D – MAY 2008 – REVISED APRIL 2013 www.ti.com Connection Diagram Figure 1. 20-Pin HTSSOP, Top View See PWP0020A Package PIN DESCRIPTIONS Pin(s) Name Description Application Information 1 SS/TRK Soft-Start or Tracking control input An internal 4.5 µA current source charges an external capacitor to set the soft-start rate. The PWM can track to an external voltage ramp with a low impedance source. If left open, an internal 1 ms SS ramp is activated. 2 FB Feedback input to the error amplifier This pin is connected to the inverting input of the internal from the regulated output transconductance error amplifier. An 800 mV reference is internally connected to the non-inverting input of the error amplifier. 3 PGOOD Power good output signal Open drain output indicating the output voltage is regulating within tolerance. A pull-up resistor of 10 k Ω to 100 kΩ is recommended if this function is used. 4 COMP Output of the internal error amplifier and The loop compensation network should be connected between the input to the Pulse Width Modulator COMP pin and the AGND pin. 5,6,15,16 VIN Input supply voltage Nominal operating range: 4.5V to 36V. 7,8,13,14 SW Switch pin The drain terminal of the internal Synchronous Rectifier power NMOSFET and the source terminal of the internal Control power NMOSFET. 9,10,11 GND Ground Internal reference for the power MOSFETs. 12 AGND Analog ground Internal reference for the regulator control functions. 17 BOOT Boost input for bootstrap capacitor An internal diode from VCC to BOOT charges an external capacitor required from SW to BOOT to power the Control MOSFET gate driver. 18 VCC Output of the high voltage linear VCC tracks VIN up to about 7.2V. Above VIN = 7.2V, VCC is regulated regulator. The VCC voltage is regulated to approximately 5.5 Volts. A 0.1 µF to 1 µF ceramic decoupling to approximately 5.5V. capacitor is required. The VCC pin is an output only. 19 EN Enable or UVLO input An external voltage divider can be used to set the line undervoltage lockout threshold. If the EN pin is left unconnected, a 2 µA pull-up current source pulls the EN pin high to enable the regulator. 20 SYNC Frequency synchronization input An external clock connected to this pin will set the switching frequency. If left open the device will operate at approximately 200 kHz. EP Exposed Exposed pad Exposed metal pad on the underside of the package with a weak Pad electrical connection to GND. Connect this pad to the PC board ground plane in order to improve heat dissipation. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 2 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM20333 |
Ähnliche Teilenummer - LM20333 |
|
Ähnliche Beschreibung - LM20333 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |