Datenblatt-Suchmaschine für elektronische Bauteile |
|
LC87F2R04A Datenblatt(PDF) 10 Page - ON Semiconductor |
|
LC87F2R04A Datenblatt(HTML) 10 Page - ON Semiconductor |
10 / 25 page LC87F2R04A No.A1622-10/25 Port Output Types The table below lists the types of port outputs and the presence/absence of a pull-up resistor. Data can be read into any input port even if it is in the output mode. Port Name Option selected in units of Option type Output type Pull-up resistor P00 to P07 1 bit 1 CMOS Programmable (Note 1) 2 Nch-open drain No P10 to P17 1 bit 1 CMOS Programmable 2 Nch-open drain Programmable P20 to P21 1 bit 1 CMOS Programmable 2 Nch-open drain Programmable P70 - No Nch-open drain Programmable Note 1: The control of the presence or absence of the programmable pull-up resistors for port 0 and the switching between low-and high-impedance pull-up connection is exercised in nibble (4-bit) units (P00 to 03 or P04 to 07). User Option Table Option Name Option Type Mask version *1 Flash Version Option Selected in Units of Option Selection Port output type P00 to P07 1 bit CMOS Nch-open drain P10 to P17 1 bit CMOS Nch-open drain P20 to P21 1 bit CMOS Nch-open drain Program start address - × *2 - 00000h 01E00h Low-voltage detection reset function Detect function - Enable: Use Disable: Not Used Detect level - 7-level Power-on reset function Power-On reset level - 8-level *1: Mask option selection-No change possible after mask is completed. *2: Program start address of the mask version is 00000h. Recommended Unused Pin Connections Port Name Recommended Unused Pin Connections Board Software P00 to P07 Open Output low P10 to P17 Open Output low P20 to P21 Open Output low P70 Open Output low CF1 Pulled low with a 100k Ω resistor or less General-purpose input port CF2 Pulled low with a 100k Ω resistor or less General-purpose input port On-chip Debugger Pin Connection Requirements For the treatment of the on-chip debugger pins, refer to the separately available documents entitled "RD87 on-chip debugger installation manual" and "LC872000 series on-chip debugger pin connection requirements" Notes on CF1 and CF2 Pins • When using as general-purpose input ports Since the CF1 and CF2 pins are configured as CF oscillator pins at system reset time, it is necessary to add a current limiting resistor of 1k Ω or greater to the CF2 pin in series when using them as general-purpose input pins. |
Ähnliche Teilenummer - LC87F2R04A |
|
Ähnliche Beschreibung - LC87F2R04A |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |