Datenblatt-Suchmaschine für elektronische Bauteile |
|
LC898240 Datenblatt(PDF) 11 Page - ON Semiconductor |
|
LC898240 Datenblatt(HTML) 11 Page - ON Semiconductor |
11 / 23 page LC898240 www.onsemi.com 11 WSEL acceleration curve selection (R/W) Address Default Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 0002h 00h - - - - WSEL_REG[3:0] It is effective during the register control mode (AIFSEL = 1). WSEL_REG[3:0] = 0h: the acceleration curve #0 WSEL_REG[3:0] = 1h: the acceleration curve #1 WSEL_REG[3:0] = 2h: the acceleration curve #2 WSEL_REG[3:0] = 3h: the acceleration curve #3 WSEL_REG[3:0] = 4h: the acceleration curve #4 WSEL_REG[3:0] = 5h: the acceleration curve #5 WSEL_REG[3:0] = 6h: the acceleration curve #6 WSEL_REG[3:0] = 7h: the acceleration curve #7 WSEL_REG[3:0] = 8h: the acceleration curve #8 WSEL_REG[3:0] = 9h - Fh: N.A. INTP interpolation setting between steps (R/W) Address Default Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 0003h 00h - - - - - - INTP_REG[1:0] It is effective during the register control mode (AIFSEL = 1). INTP_REG[1:0] = 0h: not interpolation INTP_REG[1:0] = 1h: interpolate 1 point between the steps based on E2PROM data INTP_REG[1:0] = 2h: interpolate 3 point between the steps based on E2PROM data INTP_REG[1:0] = 3h: interpolate 7 point between the steps based on E2PROM data DSKIP skip setting at deceleration (R/W) Address Default Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 0004h 00h - - - - - - DSKIP[1:0] The number of skip of the acceleration curve data for deceleration DSKIP = 0: no skip DSKIP = 1: 1 point skip DSKIP = 2: 2 points skip DSKIP = 3: 3 points skip SETST wait time for acceleration R/W Address Default Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 0005h 00h SETST[7:0] Waiting time for acceleration ����������������������������������������=��������������������������������������������������������������������������������[7:0] Where, ����������������������������������������:waitingtime[s] ����������������������������������������:initialaccelerationpulsewidth[s] SETED wait time for stop R/W Address Default Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 0006h 00h SETED[7:0] Waiting time for stop ����������������������������������������=��������������������������������������������������������������������������������[7:0] Where, ����������������������������������������:waitingtime[s] ����������������������������������������:initialaccelerationpulsewidth[s] STMODEconstant speed period programming mode selection (R/W) Address Default Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 0007h 00h - - - - - - - STMODE STMODE = 0: continue rotation at the constant speed after the acceleration until START = 0 STMODE = 1: rotate at the constant speed after the acceleration for the number of steps which is set in the register STCNT, followed by automatic deceleration and stop START must be set 0 after the motor stops. |
Ähnliche Teilenummer - LC898240 |
|
Ähnliche Beschreibung - LC898240 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |