Datenblatt-Suchmaschine für elektronische Bauteile |
|
ADC10D020 Datenblatt(PDF) 4 Page - Texas Instruments |
|
|
ADC10D020 Datenblatt(HTML) 4 Page - Texas Instruments |
4 / 39 page ADC10D020 SNAS143D – SEPTEMBER 2001 – REVISED MARCH 2013 www.ti.com PIN DESCRIPTIONS AND EQUIVALENT CIRCUITS (continued) Pin No. Symbol Equivalent Circuit Description Digital clock input for both converters. The analog inputs are 33 CLK sampled on the falling edge of this clock input. Output Bus Select. With this pin at a logic high, both the “I” and the “Q” data are present on their respective 10-bit output buses (Parallel 2 OS mode of operation). When this pin is at a logic low, the “I” and “Q” data are multiplexed onto the “I” output bus and the “Q” output lines all remain at a logic low (multiplexed mode). Offset Correct pin. A low-to-high transition on this pin initiates an independent offset correction sequence for each converter, which takes 34 clock cycles to complete. During this time 32 conversions 31 OC are taken and averaged. The result is subtracted from subsequent conversions. Each input pair should have 0V differential value during this entire 34 clock period. Output Format pin. When this pin is LOW the output format is Offset Binary. When this pin is HIGH the output format is 2's complement. 32 OF This pin may be changed asynchronously, but this will result in errors for one or two conversions. Standby pin. The device operates normally with a logic low on this and the PD (Power Down) pin. With this pin at a logic high and the 34 STBY PD pin at a logic low, the device is in the standby mode where it consumes just 27 mW of power. It takes just 800 ns to come out of this mode after the STBY pin is brought low. Power Down pin that, when high, puts the converter into the Power Down mode where it consumes less than 1 mW of power. It takes 35 PD less than 1 ms to recover from this mode after the PD pin is brought low. If both the STBY and PD pins are high simultaneously, the PD pin dominates. This pin sets the internal signal gain at the inputs to the ADCs. With this pin low the full scale differential input peak-to-peak signal is 36 GAIN equal to VREF. With this pin high the full scale differential input peak- to-peak signal is equal to 2 x VREF.. 3V TTL/CMOS-compatible Digital Output pins that provide the conversion results of the I and Q inputs. I0 and Q0 are the LSBs, I9 and Q9 are the MSBs. Valid data is present just after the rising edge 8 thru 27 I0–I9 and Q0–Q9 of the CLK input in the Parallel mode. In the multiplexed mode, I- channel data is valid on I0 through I9 when the I/Q output is high and the Q-channel data is valid on I0 through I9 when the I/Q output is low. Output data valid signal. In the multiplexed mode, this pin transitions from low to high when the data bus transitions from Q-data to I-data, 28 I/Q and from high to low when the data bus transitions from I-data to Q- data. In the Parallel mode, this pin transitions from low to high as the output data changes. Positive analog supply pin. This pin should be connected to a quiet voltage source of +2.7V to +3.6V. VA and VD should have a common 40, 41 VA supply and be separately bypassed with 10 µF to 50 µF capacitors in parallel with 0.1 µF capacitors. Digital supply pin. This pin should be connected to a quiet voltage source of +2.7V to +3.6V. VA and VD should have a common supply 4 VD and be separately bypassed with 10 µF to 50 µF capacitors in parallel with 0.1 µF capacitors. Digital output driver supply pins. These pins should be connected to 6, 30 VDR a voltage source of +1.5V to VD and be bypassed with 10 µF to 50 µF capacitors in parallel with 0.1 µF capacitors. 3, 39, 42, The ground return for the analog supply. AGND and DGND should AGND 46 be connected together close to the ADC10D020 package. The ground return for the digital supply. AGND and DGND should be 5 DGND connected together close to the ADC10D020 package. 7, 29 DR GND The ground return of the digital output drivers. 4 Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated Product Folder Links: ADC10D020 |
Ähnliche Teilenummer - ADC10D020 |
|
Ähnliche Beschreibung - ADC10D020 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |