Datenblatt-Suchmaschine für elektronische Bauteile |
|
LM3525M-L Datenblatt(PDF) 8 Page - Texas Instruments |
|
|
LM3525M-L Datenblatt(HTML) 8 Page - Texas Instruments |
8 / 17 page LM3525 SNVS051D – FEBRUARY 2000 – REVISED MARCH 2013 www.ti.com Adequate capacitance must be connected to the input of the device to limit the input voltage drop during a hot- plug event to less than 330 mV. For a few tens of µs, the host must supply the inrush current to the peripheral, charging its bulk capacitance to Vbus. This current is initially supplied by the input capacitor. A 33 µF 16V tantalum capacitor is recommended. In choosing the capacitors, special attention must be paid to the Effective Series Resistance, ESR, of the capacitors to minimize the IR drop across the capacitor's ESR. SOFT START To eliminate the upstream voltage droop caused by the high in-rush current drawn by the output capacitors, the inrush current is internally limited to 1.0A. TRANSIENT OVER-CURRENT DELAY In USB applications, it is required that output bulk capacitance is utilized to support hot-plug events. During hot- plug events, inrush currents may also cause the flag to go active. Since these conditions are not valid over- current faults, the USB controller must ignore the flag during these events. High transient current is also generated when switch is enabled and large values of capacitance at the output have to be rapidly charged. The inrush currents created could exceed the short circuit current limit threshold of the device forcing it into the current limit mode. The capacitor is charged with the maximum available short circuit current set by the LM3525. The duration of the inrush current depends on the size of the output capacitance and load current. Since this is not a valid fault condition, the LM3525 delays the generation of the fault flag for 1 ms. If condition persists due to other causes such as a short, a fault flag is generated after a 1 ms delay has elapsed. The LM3525's 1 ms delay in issuing the fault flag is adequate for most applications. If longer delays are required, an RC filter as shown in Figure 14 may be used. Figure 14. Transient Fitter PCB LAYOUT CONSIDERATIONS In order to meet the USB requirements for voltage drop, droop and EMI, each component used in this circuit must be evaluated for its contribution to the circuit performance as shown in Figure 15. The PCB layout rules and guidelines must be followed. • Place the switch as close to the USB connector as possible. Keep all Vbus traces as short as possible and use at least 50-mil, 1 ounce copper for all Vbus traces. Solder plating the traces will reduce the trace resistance. • Avoid vias as much as possible. If vias are used, use multiple vias in parallel and/or make them as large as possible. • Place the output capacitor and ferrite beads as close to the USB connector as possible. • If ferrite beads are used, use wires with minimum resistance and large solder pads to minimize connection resistance. 8 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated Product Folder Links: LM3525 |
Ähnliche Teilenummer - LM3525M-L |
|
Ähnliche Beschreibung - LM3525M-L |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |