Datenblatt-Suchmaschine für elektronische Bauteile |
|
LM4951 Datenblatt(PDF) 4 Page - Texas Instruments |
|
|
LM4951 Datenblatt(HTML) 4 Page - Texas Instruments |
4 / 23 page LM4951 SNAS244N – AUGUST 2004 – REVISED MAY 2013 www.ti.com Electrical Characteristics VDD = 7.5V (1) (2) The following specifications apply for VDD = 7.5V, AV-BTL = 6dB, RL = 8Ω unless otherwise specified. Limits apply for TA = 25°C. Symbol Parameter Conditions LM4951 Units (Limits) Typical(3) Limit(4)(5) IDD Quiescent Power Supply Current VIN = 0V, IO = 0A,RL = 8Ω 2.5 4.5 mA (max) ISD Shutdown Current VSHUTDOWN = GND (6) 0.01 5 µA (max) VOS Offset Voltage 5 30 mV (max) VSDIH Shutdown Voltage Input High 1.2 V (min) VSDIL Shutdown Voltage Input Low 0.4 V (max) Rpulldown Pulldown Resistor on S/D 75 45 k Ω (min) TWU Wake-up Time CB = 1.0µF 25 35 ms Tsd Shutdown time CB = 1.0µF 10 ms (max) 150 °C (min) TSD Thermal Shutdown Temperature 170 190 °C (max) THD = 1% (max); f = 1kHz PO Output Power 1.8 1.5 W (min) RL = 8Ω Mono BTL PO = 600mWrms; f = 1kHz THD+N Total Harmomic Distortion + Noise 0.07 0.5 % (max) AV-BTL = 6dB PO = 600mWrms; f = 1kHz THD+N Total Harmomic Distortion + Noise 0.35 % AV-BTL = 26dB A-Weighted Filter, Ri = Rf = 20kΩ εOS Output Noise 10 µV Input Referred, Note 10 VRIPPLE = 200mVp-p, f = 217Hz, PSRR Power Supply Rejection Ratio 66 56 dB (min) CB = 1.0μF, Input Referred (1) All voltages are measured with respect to the GND pin, unless otherwise specified. (2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not specified for parameters where no limit is given, however, the typical value is a good indication of device performance. (3) Typicals are measured at 25°C and represent the parametric norm. (4) Limits are specified to AOQL (Average Outgoing Quality Level). (5) Datasheet min/max specification limits are specified by design, test, or statistical analysis. (6) Shutdown current is measured in a normal room environment. The Shutdown pin should be driven as close as possible to GND for minimum shutdown current. 4 Submit Documentation Feedback Copyright © 2004–2013, Texas Instruments Incorporated Product Folder Links: LM4951 |
Ähnliche Teilenummer - LM4951 |
|
Ähnliche Beschreibung - LM4951 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |