Datenblatt-Suchmaschine für elektronische Bauteile |
|
ADC10064 Datenblatt(PDF) 3 Page - Texas Instruments |
|
ADC10064 Datenblatt(HTML) 3 Page - Texas Instruments |
3 / 22 page ADC10061, ADC10062, ADC10064 www.ti.com SNAS069E – JUNE 1999 – REVISED MARCH 2013 NOTE: The ADC10061 and ADC10062 are obsolete; shown for reference only. PIN DESCRIPTIONS Pin Function Description DVCC, AVCC Digital and analog positive supply voltage inputs. Connect both to the same voltage source, but bypass separately with a 0.1 µF ceramic capacitor in parallel with a 10 µF tantalum capacitor to ground at each pin. INT Active low interrupt output. INT goes low at the end of each conversion, and returns high following the rising edge of RD. S/H Sample/Hold control input. When this pin is forced low (and CS is low), the analog input signal is sampled and a new conversion is initiated. RD Active low read control input. When this RD and CS are low, any data present in the output registers will be placed onto the data bus. CS Active low Chip Select control input. When low, this pin enables the RD and S/H pins. S0, S1 On the multiple-input devices (ADC10062 and ADC10064), these pins select the analog input that will be connected to the A/D during the conversion. The input is selected based on the state of S0 and S1 when S/H makes its High-to-Low transition (See Timing Diagrams). The ADC10064 includes both S0 and S1. The ADC10062 includes just S0, and the ADC10061 has neither. VREF−, VREF+ Reference voltage inputs. They may be placed at any voltage between GND and VCC, but VREF+ must be greater than VREF−. An input voltage equal to VREF− produces an output code of 0, and an input voltage equal to (VREF+ − 1 LSB) produces an output code of 1023. VIN, VIN0, VIN1, Analog input pins. The ADC10061 has one input (VIN), the ADC10062 has two inputs (VIN0 and VIN1), and the VIN2, VIN3 ADC10064 has four inputs (VIN0, VIN1, VIN2 and VIN3). The impedance of the input source should be less than 500Ω for best accuracy and conversion speed. For accurate conversions, no input pin (even one that is not selected) should be driven more than 50 mV above VCC or 50 mV below ground. GND, AGND, Power supply ground pins. The ADC10061 has a single ground pin (GND), and the ADC10062 and ADC10064 have DGND separate analog and digital ground pins (AGND and DGND) for separate bypassing of the analog and digital supplies. The ground pins should be connected to a stable, noise-free system ground. For the devices with two ground pins, both pins should be returned to the same potential. DB0–DB9 TRI-STATE data output pins. SPEED ADJ (ADC10062 and ADC10064 only). This pin is normally left unconnected, but by connecting a resistor between this pin and ground, the conversion time can be reduced. See Typical Performance Characteristics and the table of Electrical Characteristics. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 3 Product Folder Links: ADC10061 ADC10062 ADC10064 |
Ähnliche Teilenummer - ADC10064 |
|
Ähnliche Beschreibung - ADC10064 |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |