CS5509-ASZ datasheet(10/23 Pages) CIRRUS

Teilenummer	CS5509-ASZ

Bauteilbeschribung	SINGLE SUPPLY 16BIT A/D CONVERTER

Download	23 Pages

Scroll/Zoom	100%

Hersteller	CIRRUS [Cirrus Logic]

Direct Link	http://www.cirrus.com

Logo

10 / 23 page

CS5509

10

DS125F2

GENERAL DESCRIPTION

The CS5509 is a low power, 16-bit, monolithic

CMOS A/D converter designed specifically for

measurement of dc signals. The CS5509 includes a

delta-sigma charge-balance converter, a voltage

reference, a calibration microcontroller with

SRAM, a digital filter and a serial interface.

The CS5509 is optimized to operate from a 32.768

kHz crystal but can be driven by an external clock

whose frequency is between 30kHz and 330kHz.

When the digital filter is operated with a 32.768

kHz clock, the filter has zeros precisely at 50 and

60 Hz line frequencies and multiples thereof.

The CS5509 uses a "start convert" command to

start a convolution cycle on the digital filter. Once

the filter cycle is completed, the output port is up-

dated.When operated with a 32.768kHz clock the

ADC converts and updates its output port at 20

samples/sec.The output port operates in a synchro-

nous externally-clocked interface format.

THEORY OF OPERATION

Basic Converter Operation

The CS5509 A/D converter has three operating

states. These are stand-by, calibration, and conver-

sion. When power is first applied, an internal pow-

er-on reset delay of about 10 ms resets all of the

logic in the device. The oscillator must then begin

oscillating before the device can be considered

functional. After the power-on reset is applied, the

device enters the wake-up period for 1800 clock

cycles after clock is present. This allows the delta-

sigma modulator and other circuitry (which are op-

erating with very low currents) to reach a stable

bias condition prior to entering into either the cali-

bration or conversion states. During the 1800 cycle

wake-up period, the device can accept an input

command. Execution of this command will not oc-

cur until the complete wake-up period elapses. If

no command is given, the device enters the standby

state.

Calibration

After the initial application of power, the CS5509

must enter the calibration state prior to performing

accurate conversions. During calibration, the chip

executes a two-step process. The device first per-

forms an offset calibration and then follows this

with a gain calibration. The two calibration steps

determine the zero reference point and the full scale

reference point of the converter's transfer function.

From these points it calibrates the zero point and a

gain slope to be used to properly scale the output

digital codes when doing conversions.

The calibration state is entered whenever the CAL

and CONV pins are high at the same time. The state

of the CAL and CONV pins at power-on are recog-

nized as commands, but will not be executed until

the end of the 1800 clock cycle wake-up period.

If CAL and CONV become active (high) during the

1800 clock cycle wake-up time, the converter will

wait until the wake-up period elapses before exe-

cuting the calibration. If the wake-up time has

elapsed, the converter will be in the standby mode

waiting for instruction and will enter the calibration

cycle immediately if CAL and CONV become ac-

tive. The calibration lasts for 3246 clock cycles.

Calibration coefficients are then retained in the

SRAM (static RAM) for use during conversion.

The state of BP/UP is ignored during calibration

but should remain stable throughout the calibration

period to minimize noise.

When conversions are performed in unipolar mode

or in bipolar mode, the converter uses the same cal-

ibration factors to compute the digital output code.

The only difference is that in bipolar mode the on-

chip microcontroller offsets the computed output

word by a code value of 8000H. This means that the

bipolar measurement range is not calibrated from

full scale positive to full scale negative. Instead it is

calibrated from the bipolar zero scale point to full

scale positive. The slope factor is then extended be-

low bipolar zero to accommodate the negative in-

CS5509-ASZ Datenblatt(PDF) 10 Page - Cirrus Logic

CS5509-ASZ Datenblatt(HTML) 10 Page - Cirrus Logic

Ähnliche Teilenummer - CS5509-ASZ

Ähnliche Beschreibung - CS5509-ASZ

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

Datenblatt Download

Link URL