LC78616PE

www.onsemi.com

4

Parameter

Symbol

Pin Names

Type

Conditions

MIN

TYP

MAX

Unit

Current drain

IDD1

DVDD, AVDD,

XVDD, VVDD1

40

60

mA

High-level

input current

IIH

RESB, MODE, MODE3,

CE, CL, DI,

CONT00, CONT01, CONT02,

CONT03, CONT04, CONT05,

CONT08, CONT09, CONT10,

DO,

SDDAT00 to 15,

SDADRS11, SDADRS12

Schmitt

VIN = VDD

Built-in

Pull-down

Resistor

OFF

10.00

μA

Low-level

input current

IIL

RESB, TEST, MODE3,

CE, CL, DI,

CONT00, CONT01, CONT02,

CONT03, CONT04, CONT05,

CONT08, CONT09, CONT10,

SDDAT00 to 15,

SDADRS11, SDADRS12

Schmitt

VIN = 0.0V

Built-in

Pull-down

Resistor

OFF

10.00

High-level

output voltage

VOH(1)

DO, BUSYB,

CONT00, CONT01, CONT02,

CONT03, CONT05,

CONT08, CONT09, CONT10,

SDDAT00 to SDDAT15,

SDADRS00 to SDADRS12,

SDBA,

SDCKE, SDCSB, SDRASB,

SDCASB, SDWEB, SDDQM

CMOS

IOH =

2 mA

VDD

0.6

V

VOH(2) CL, DI, CONT04, SDCLK

CMOS

IOH =

4 mA

Low-level

output voltage

VOL(1)

DO, BUSYB,

CONT00, CONT01, CONT02,

CONT03, CONT05,

CONT08, CONT09, CONT10,

SDDAT00 to SDDAT15,

SDADRS00 to SDADRS12,

SDBA,

SDCKE, SDCSB, SDRASB,

SDCASB, SDWEB, SDDQM

CMOS

IOL = 2 mA

0.40

VOL(2) CL, DI, CONT04, SDCLK

CMOS

IOL = 4 mA

Output

off-leakage

current

IOFF(1) PDOUT0, PDOUT1

Hi-Z Out

10.00

10.00

μA

IOFF(2) DO

Hi-Z Out

10.00

10.00

Built-in

Pull-down

resistor

RPD

CE,

CONT00, CONT01, CONT02,

CONT03, CONT04, CONT05,

CONT08, CONT09, CONT10,

SDDAT00 to SDDAT15,

SDADRS11,SDADRS12

50

100

200

kΩ

Charge pump

output current

IPDOH

PDOUT1, PDOUT0

PCKIST =

100 kΩ

Current value

Setting : 1x

35

50

65

μA

IPDOL

PDOUT1, PDOUT0

65

50

35

(Notes)

 Connect and use the pull-up or the pull-down resister with the outside when you use serial communications because the terminal

DO is 3- State output (initial state).

 The DO, BUSYB, CONT00, CONT01, CONT02, CONT03, CONT04, CONT05, CONT08, CONT09 and CONT10 pins can be

used as the N channel open drain pins. When used as the N channel open drain pin, external pull-up resistor must be connected to

those pins.

Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be

indicated by the Electrical Characteristics if operated under different conditions.