Datenblatt-Suchmaschine für elektronische Bauteile
  German  ▼
ALLDATASHEETDE.COM

X  

1--21046--3 Datenblatt(PDF) 2 Page - Tyco Electronics

Teilenummer 1--21046--3
Bauteilbeschribung  Crimping Die Assemblies
Download  3 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Hersteller  MACOM [Tyco Electronics]
Direct Link  http://www.macom.com
Logo MACOM - Tyco Electronics

1--21046--3 Datenblatt(HTML) 2 Page - Tyco Electronics

  1--21046--3 Datasheet HTML 1Page - Tyco Electronics 1--21046--3 Datasheet HTML 2Page - Tyco Electronics 1--21046--3 Datasheet HTML 3Page - Tyco Electronics  
Zoom Inzoom in Zoom Outzoom out
 2 / 3 page
background image
408- 9905
Crimping Die Assemblies 58492- 1 and 58493- 1
Rev C
2
of 3
Tyco Electronics Corporation
Figure 3
Contact Wire
Barrel Against
Locator/Insulation
Stop
Stationary Die
(Crimper)
Front of
Tool
Stripped
Wire
Front of
Dies
Moving Die
(Anvil)
5. Allow the tool to open fully, then remove the
crimped contact.
4. MAINTENANCE AND INSPECTION
4.1. Maintenance
1. Remove dust, moisture and other contaminants
with a clean brush, or a soft, lint--free cloth. Do not
use objects that could damage the dies.
2. Make sure that dies are properly aligned and
that die holding screws are in place and secured.
3. Make certain that all surfaces are protected with
a thin coat of any good SAE 20 motor oil. Do not
oil excessively.
4. When dies are not in use, store in a clean, dry
area.
4.2. Inspection
Regular inspections should be performed with a
record of inspections remaining with the dies and/or
supervisory personnel responsible for them. One
inspection per month is recommended; however,
amount of use, working conditions, operator training
and skill, and established company standards should
determine frequency of inspection. The inspection
should be performed in the following sequence:
A. Visual Inspection
1. Remove all lubrication and accumulated film by
immersing the dies in a suitable commercial
degreaser that will not affect paint or plastic
material.
SAE is a trademark of SAE International Corporation.
2. Make sure all die holding screws are in place
and secured.
3. Check all bearing surfaces for wear. Replace
worn components.
4. Inspect the crimp area for flattened, chipped,
cracked, worn, or broken areas. If damage is
evident, the dies must be repaired before returning
them to service.
B. Crimp Height Inspection
This inspection incorporates the use of a crimp height
comparator (micrometer with a modified anvil) as
shown in Figure 4. Detailed information on obtaining
and using a crimp height comparator can be found in
instruction sheet 408--7424.
Point Positioned on
Center of Wire Barrel
Opposite Seam
Modified Anvil
Crimp Height
(See Table)
DIE ASSEMBLY
MAXIMUM WIRE
SIZE (AWG)
CRIMP HEIGHT
58492--1
14
2.44 [.096]
58493--1
16
2.21 [.087]
Figure 4
Proceed as follows:
1. Refer to Figure 4 and select a contact and
maximum size wire for the dies.
2. Refer to Section 3, CRIMPING PROCEDURE,
and crimp the contact accordingly.
3. Using the crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4.
If the crimp height conforms to that shown in Figure 4,
the dies are considered dimensionally correct and
should be lubricated with a thin coat of any good SAE
20 motor oil. If not, the dies must be repaired or
replaced. Refer to Section 5, REPLACEMENT AND
REPAIR.
5. REPLACEMENT AND REPAIR
Customer--replaceable parts are listed in Figure 5.
A complete inventory should be stocked and
controlled to prevent lost time when replacement of
parts is necessary. Parts other than those listed
should be replaced by Tyco Electronics to ensure
quality and reliability. Order replacement parts


Ähnliche Teilenummer - 1--21046--3

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
Tyco Electronics
1--21048--0 MACOM-1--21048--0 Datasheet
273Kb / 5P
   Pneumatic Head Assembly
More results

Ähnliche Beschreibung - 1--21046--3

HerstellerTeilenummerDatenblattBauteilbeschribung
logo
TE Connectivity Ltd
408-2822 TEC-408-2822 Datasheet
186Kb / 7P
   Crimping Die Assemblies
408-9278 TEC-408-9278 Datasheet
272Kb / 5P
   Crimping Die Assemblies
408-9279 TEC-408-9279 Datasheet
138Kb / 5P
   Crimping Die Assemblies
408-6877 TEC-408-6877 Datasheet
299Kb / 5P
   Crimping Die Assemblies
logo
Tyco Electronics
408-9177 MACOM-408-9177 Datasheet
142Kb / 5P
   Crimping Die Assemblies
logo
TE Connectivity Ltd
408-8704 TEC-408-8704 Datasheet
519Kb / 10P
   Crimping Die Assemblies
408-2786 TEC-408-2786 Datasheet
134Kb / 5P
   Crimping Die Assemblies
408-2281 TEC-408-2281 Datasheet
520Kb / 12P
   Crimping Die Assemblies
408-8703 TEC-408-8703 Datasheet
226Kb / 6P
   Crimping Die Assemblies
408-2710 TEC-408-2710 Datasheet
328Kb / 5P
   AMPOWER Crimping Die Assemblies
More results


Html Pages

1 2 3


Datenblatt Download

Go To PDF Page


Link URL




Privatsphäre und Datenschutz
ALLDATASHEETDE.COM
War ALLDATASHEET hilfreich?  [ DONATE ] 

Über Alldatasheet   |   Werbung   |   Kontakt   |   Privatsphäre und Datenschutz   |   Linktausch   |   Hersteller
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com