Datenblatt-Suchmaschine für elektronische Bauteile |
|
LM2796TL Datenblatt(PDF) 4 Page - National Semiconductor (TI) |
|
|
LM2796TL Datenblatt(HTML) 4 Page - National Semiconductor (TI) |
4 / 8 page Electrical Characteristics (Notes 2, 7) (Continued) Limits in standard typeface and typical values apply for T J =25 oC. Limits in boldface type apply over the full operating junction temperature range (-30˚C ≤ T J ≤ +85˚C) . Unless otherwise specified: V IN = 3.6V; VDxx = 3.6V; V(EN) = 2.0V; Group A and Group B LEDs not ON simultaneously (ENA = V IN and ENB = GND, or ENA = GND and ENB = VIN); RSET = 8.35k Ω;C IN,C1, C 2, and CPOUT = 1µF. (Note 8) Symbol Parameter Condition Min Typ Max Units f SW Switching Frequency 3.0V ≤ V IN ≤ 4.2V 325 500 675 kHz t START Start-up Time I Dx = 90% steady state 100 µs 1.5x/1x Charge pump gain cross-over: Gain = 1.5 when V IN is below threshold. Gain = 1 when V IN is above threshold. 1.5x to 1x Threshold 4.75 V 1x to 1.5x Threshold 4.55 V Logic Pin Specifications: EN, ENA, ENB V IL Input Logic Low 2.7V ≤ V IN ≤ 5.5V 0 0.5 V V IH Input Logic High 2.7V ≤ V IN ≤ 5.5V 1.1 V IN V I LEAK Input Leakage Current V ENx = 0V 0.1 µA V ENx = 3V (Note 13) 10 Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under which operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. Note 2: All voltages are with respect to the potential at the GND pin. Note 3: Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ = 160˚C (typ.) and disengages at TJ = 120˚C (typ.). The thermal shutdown function is guaranteed by design. Note 4: The Human body model is a 100pF capacitor discharged through a 1.5k resistor into each pin. The machine model is a 200pF capacitor discharged directly into each pin. MIL-STD-883 3015.7 Note 5: In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP = 125˚C), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the part/package in the application (θJA), as given by the following equation: TA-MAX =TJ-MAX-OP –(θJA xPD-MAX). Note 6: Junction-to-ambient thermal resistance is highly dependent on application and board layout. In applications where high maximum power dissipation exists, special care must be paid to thermal dissipation issues in board design. Note 7: Min and Max limits are guaranteed by design, test, or statistical analysis. Typical numbers are not guaranteed, but do represent the most likely norm. Note 8: CIN,COUT,C1, and C2 : Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) used in setting electrical characteristics Note 9: If both LED groups are to be ON simultaneously, the maximum VDxx voltage may need to be derated, depending on minimum input voltage conditions. Refer to the "MAXIMUM OUTPUT CURRENT, MAXIMUM LED VOLTAGE, MINIMUM INPUT VOLTAGE" section. Note 10: For the two groups of outputs on a part (Group A and Group B), the following are determined: the maximum output current in the group (MAX), the minimum output current in the group (MIN), and the average output current of the group (AVG). For each group, two matching numbers are calculated: (MAX-AVG)/AVG and (AVG-MIN)/AVG. The largest number of the two (worst case) is considered the matching figure for the group. The matching figure for a given part is considered to be the highest matching figure of the two groups. The typical specification provided is the most likely norm of the matching figure for all parts. Note 11: Output resistance (ROUT) models all voltage losses in the charge pump. ROUT can be used to estimate the voltage at the charge pump output (POUT): VPout =(1.5xVIN)– (ROUT xIOUT). In the equation, IOUT is the total output current: the sum of all active Dxx output currents and all current drawn from POUT. The equation applies when the charge pump is operating with a gain of 3/2 (VIN ≤ 4.75V typ.). Note 12: Headroom voltage: VHR =VPout –VDxx . If headroom voltage requirement is not met, LED current regulation will be compromised. Note 13: There is a 300k Ω(typ.) pull-down resistor connected internally between each enable pin (EN, ENA, ENB) and GND. www.national.com 4 |
Ähnliche Teilenummer - LM2796TL |
|
Ähnliche Beschreibung - LM2796TL |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |