Datenblatt-Suchmaschine für elektronische Bauteile |
|
ACE24AC02A3OMTH Datenblatt(PDF) 5 Page - ACE Technology Co., LTD. |
|
ACE24AC02A3OMTH Datenblatt(HTML) 5 Page - ACE Technology Co., LTD. |
5 / 17 page ACE24AC02A3 Two-wire Serial EEPROM VER 1.3 5 Device Addressing The 2-wire serial bus protocol mandates an 8 bits device address word after a start bit condition to invoke valid read or write command. The first four most significant bits of the device address must be 1010, which is common to all serial EEPROM devices. The next three bits are device address bits. These three device address bits (5 th, 6th and 7th) are not cared and could be coded from 000 (b) to 111 (b). Only one ACE24AC02A3 device can be used on the on 2-wire bus. If a match is made, the EEPROM device outputs an acknowledge signal after the 8 th read/write bit, otherwise the chip will go into standby mode. The last or 8th bit is a read/write command bit. If the 8th bit is at VIH then the chip goes into read mode. If a “0” is detected, the device enters programming mode. Write Operations A. Byte Write A byte write operation starts when a micro-controller sends a start bit condition, follows by a proper EEPROM device address and then a write command. If the device address bits match the chip select address, the EEPROM device will acknowledge at the 9 th clock cycle. The micro-controller will then send the rest of the lower 8 bits word address. At the 18 th cycle, the EEPROM will acknowledge the 8-bit address word. The micro-controller will then transmit the 8 bit data. Following an acknowledge signal from the EEPROM at the 27 th clock cycle, the micro-controller will issue a stop bit. After receiving the stop bit, the EEPROM will go into a self-timed programming mode during which all external inputs will be disabled. After a programming time of TWC, the byte programming will finish and the EEPROM device will return to the standby mode. B. Page Write A page write is similar to a byte write with the exception that one to sixteen bytes can be programmed along the same page or memory row. All ACE24AC02A3 are organized to have 16 bytes per memory row or page. With the same write command as the byte write, the micro-controller does not issue a stop bit after sending the 1 st byte data and receiving the acknowledge signal from the EEPROM on the 27th clock cycle. Instead it sends out a second 8-bit data word, with the EEPROM acknowledging at the 36 th cycle. This data sending and EEPROM acknowledging cycle repeats until the micro-controller sends a stop bit after the n × 9 th clock cycle. After which the EEPROM device will go into a self- timed partial or full page programming mode. After the page programming completes after a time of TWC, the devices will return to the standby mode. The least significant 4 bits of the word address (column address) increments internally by one after receiving each data word. The rest of the word address bits (row address) do not change internally, but pointing to a specific memory row or page to be programmed. The first page write data word can be of any column address. Up to 16 data words can be loaded into a page. If more then 16 data |
Ähnliche Teilenummer - ACE24AC02A3OMTH |
|
Ähnliche Beschreibung - ACE24AC02A3OMTH |
|
|
Link URL |
Privatsphäre und Datenschutz |
ALLDATASHEETDE.COM |
War ALLDATASHEET hilfreich? [ DONATE ] |
Über Alldatasheet | Werbung | Kontakt | Privatsphäre und Datenschutz | Linktausch | Hersteller All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |